manualshive.com logo in svg

Cooper & Hunter CH-HP3.0SWHK, Руководство пользователя, Страница: 12 / 44

Поделиться
Скачать
Cooper & Hunter CH-HP3.0SWHK Скачать руководство пользователя страница 12

Air Source Heat Pump Water Heater 

8 

3.3 Advantages 

 Efficient and Energy-Saving 

The  outdoor  unit  of  this  product  adopts  an  electronic  expansion  valve  for 

adaptive control. It automatically adjusts its opening size based on the unit operating 

conditions, and uses the heat in the air to heat up domestic water, so that the unit 

always  runs  at  optimal  performance  as  well  as  ensuring  reliability.  The  water  tank 

adopts  an  externally  wrapped  microchannel  heat  exchanger,  and  is  in  planar 

contact  with  the  inner container,  which  features higher  efficiency  in  heat  exchange 

and a high pressure-bearing capability. Effective thermally-conductive materials are 

used between the microchannel heat exchanger and the inner container of the water 

tank to enhance heat transfer. 

In  testing conditions  of  the  unit,  the coefficient  of  performance  (COP)  reaches 

up to 2.9, and the operating costs are more economical than conventional heaters. 

 Reliability and Durability 

The unit adopts a dedicated compressor, which can withstand high temperature 

and  high  pressure.  The  water  tank  adopts  a  stainless  steel  inner  container  made 

based  advanced  technologies  and  is  equipped  with  a  long-lifespan  Mg-Stick  to 

prevent corruption. The entire unit has multi-level protection to ensure durable and 

reliable use. 

 Environment-Friendly and Safe 

The  unit  uses  the  environment-friendly  R134a  refrigerant,  which  has  no 

atmospheric  pollution  and  has  no  potential  safety  hazards  such  as  monoxide 

poisoning to for safety purposes. 

 Simple and Convenient Installation 

The  installation  is not subject to  any  environmental  limitation.  The  unit can  be 

installed  in  the  kitchen,  bathroom,  balcony,  garage,  storage  room,  or  basement 

according  to  actual  living  conditions,  and  requires  no  special  care.  It  applies  to 

places such as household use and villa suites. It is a no-loop waterway system, and 

can be easily and conveniently installed. 

 Luxury Configurations: 

The  unit  is  equipped  with  a  high-end  ultra-thin  touch-wired  controller,  which 

provides four heating modes: hot water, saving, preset, and night modes. The unit 

provides a proper water temperature range from 35°C to 70°C. It provides functions 

such as fast heating, timer switch, and "i-KNOW." 

Содержание CH-HP3.0SWHK













































Отзывы:

Нет отзывов