Cooper & Hunter CH-HP3.0SWHK Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 44

Cooper & Hunter CH-HP3.0SWHK Скачать руководство пользователя страница 23

Air Source Heat Pump Water Heater

19

8 Installation Diagram of the Unit

Figure 8-1 Installation diagram of the unit

Table 8-1 Dimensions and specifications

Name

Interfacing Pipe Screw Thread

Hot water outlet of the water tank

G1/2

Cold water inlet of the water tank

G1/2

In the installation diagram of the unit, the dotted lines indicate the installation

diagram for installing the preheating water return function. With this function, it is

ensured that the water in the pipe between the water tank and the location for water

use is hot. That is, the user can always use hot water when opening the tap. This

does not require the user to drain the cold water for use of hot water. This function

requires the installation of a water return system (water return pump, water return

pipes, and water return check valve and temperature sensor for water return pipes)

during the installation of the unit. Wilo RS15/6 is recommended for the water return

pump. If other pumps are used, the requirements are as follows: flow

≥ 1 m

3,

; lift

≥ 6

m. A length of about 10 m is recommended for the water return pipe, and a

resistance of 50 k

Ω

is recommended for the

cycle temperature sensor

.

«
...
21
22
23
24
25
...
»

Содержание CH-HP3.0SWHK













































Отзывы:

Нет отзывов