Coolmay CX-WIFI-2NET Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 93

background image

CX-WIFI-2NET module user manual

Shenzhen Coolmay Technology Co.,Ltd

www.coolmay.com

Page

15

,Total 93 Pages

2.3.2 AP-based wireless network

Because the CX-WIFI-2NET module can be set to either AP or STA, the CX-WIFI-2NET

module  can  easily  implement  the  wireless  network  of  the  ad  hoc  network.  As  shown  below.  The
CX-WIFI-2NET module No. 1 is used as an AP. Other modules and computers can be connected to
this  module  as  STAs.  It  can  also  be  connected  to  user  equipment  through  the  UART  interface;
CX-WIFI-  2  and  3  The  2NET  module  is  connected  to  the  No.  1  module  as  a  STA,  so  that  all
CX-WIFI-2NET modules can  be managed  by  a  computer.  The  self-organizing  network  mode  can
facilitate  the  unified  management  of  all  CX-WIFI-2NET  modules,  and  the  self-organizing  network
can easily expand the coverage of the entire wireless network.

«
...
13
14
15
16
17
...
»

Содержание CX-WIFI-2NET






























































































Отзывы:

Нет отзывов

Похожие инструкции для CX-WIFI-2NET

Бренд: VADDIO Страницы: 2

Бренд: Hach Страницы: 2

Бренд: Hach Страницы: 12

Бренд: Hach Страницы: 472

Бренд: Hach Страницы: 64

Бренд: V2 ELETTRONICA Страницы: 6

Бренд: Hach Страницы: 210

Бренд: Pando Страницы: 43

Бренд: Bardiani Страницы: 22

Бренд: Rheem Страницы: 2

Бренд: KAR-TECH Страницы: 55

10 AMP RVC-MPPT

Бренд: Go Power Страницы: 17

Бренд: QUANT Страницы: 24

Verafix-Cool V9406

Бренд: Honeywell Home Страницы: 2

Бренд: heat-timer Страницы: 40

FlexRIO PXIe-79 R Series

Бренд: National Instruments Страницы: 17

Бренд: Danfoss Страницы: 8

Бренд: P3 International Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды