manualshive.com logo in svg

Coolmay CX-WIFI-2NET, Руководство пользователя

Поделиться
Скачать
Coolmay CX-WIFI-2NET Скачать руководство пользователя страница 85

Shenzhen Coolmay Technology Co.,Ltd 

                                                       

CX-WIFI-2NET module user manual           

      

 

 

www.coolmay.com 

Page 

85

 , Total 93 pages 

Step 2: Configure the virtual serial port software 
 

①

  Add virtual serial port

：

 

 

Note: 
The virtual serial port is set to an unoccupied COM port on the computer; 
Network protocol selects TCP Client; 
Target IP/domain name setting 120.76.116.193 (Note: The target 
IP/domain name is Shenzhen Coolmay Technology domain name, which 
must be connected with Coolmay server); 
Target port setting 25565; 
Registration ID setting in Advanced 43589

（

Note: Each CX-WIFI-2NET 

module has a unique pair of registration IDs. Please specify the 
registration ID according to the factory parameters. The registration ID 
number corresponding to each module will be indicated on the product 
label. If you forget or not save, please ask Coolmay for help.

）

 

After the creation is successful, as shown in the figure below, and change 

the sync baud rate option in the option to unchecked: 

Содержание CX-WIFI-2NET






























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды