Coolmay CX-WIFI-2NET Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 93

background image

Shenzhen Coolmay Technology Co.,Ltd

CX-WIFI-2NET module user manual

Page

32

, Total 93 pages

www.coolmay.com

<Description>:
There are four modes on the network side: TCP Server, TCP Client, UDP server,

and UDP client.

When the module is configured as UDP server, the module remembers the last

communicated UDP client and communicates with it.While the UDP client mode only
communicates with the target IP and address. When set to TCP Server, you do not
need to enter IP address. For other settings, you need to fill in the opponent's IP
address that needs to be connected. Fill in the protocol port number at the port, and
the port numbers on both ends of the communication must be the same.

Socket B can only be TCP client to communicate with the server.
TCP connection password verification: When the module works in tcp server

mode, password verification is performed on the connected tcp client.

Note: This verification only works when the module is acting as a TCP server.

When the TCP client is connected to the TCP server of the module when it is turned
on, the first data sent to the module is the password and enter key. Password is the
one when log in to the webpage, default is “admin”. For example, the first data sent
by default should be “0x61 0x64 0x6D 0x69 0x6E 0x0D 0x0A” (hexadecimal)

3.1.7 Ethernet Function Settings

This page is used to set two Ethernet network ports of the module. Both network

«
...
30
31
32
33
34
...
»

Содержание CX-WIFI-2NET






























































































Отзывы:

Нет отзывов

Похожие инструкции для CX-WIFI-2NET

Concord express

Бренд: GE Страницы: 3

Бренд: Gardena Страницы: 16

Бренд: MADRIX Страницы: 28

Бренд: Danfoss Страницы: 7

vlt soft starter mcd 500

Бренд: Danfoss Страницы: 95

Бренд: Danfoss Страницы: 12

Бренд: Danfoss Страницы: 33

Бренд: Danfoss Страницы: 59

Бренд: Danfoss Страницы: 16

VLT AQUA Drive FC 200

Бренд: Danfoss Страницы: 91

Бренд: Danfoss Страницы: 2

Бренд: Danfoss Страницы: 100

Бренд: Danfoss Страницы: 82

Бренд: Danfoss Страницы: 18

Бренд: Danfoss Страницы: 12

OPTYMA Plus OP-LPQM

Бренд: Danfoss Страницы: 8

Бренд: Fairchild Страницы: 2

Бренд: Fairford Страницы: 233

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды