Coolmay CX-WIFI-2NET Скачать руководство пользователя страница 51

Страница: 51 / 93

Shenzhen Coolmay Technology Co.,Ltd

CX-WIFI-2NET module user manual

Page

, Total 93 pages

www.coolmay.com

When querying, sta.: returns whether the module sleeps, such as

On, indicating no sleep

Off, indicating sleep

While setting, off puts the module into sleep mode, on allows the module to exit

sleep mode. When the module enters sleep mode, enter AT+MSLP=on and the

module exits sleep mode. Mode is still command mode.

3.2.2.2.17 AT+WSCAN

Function: Search AP

Format:

AT+ WSCAN<CR>

+ok=<ap_site><CR>< LF ><CR>< LF >

parameter:

Ap_site: searched AP site

The first line of the return value is "RSSI, SSID, BSSID, Channel, Encryption,

Authentication", which are strong signals.

Degree, network name, MAC address, channel, authentication mode, encryption

algorithm.

3.2.2.2.18 AT+TCPLK

Function: Query whether the TCP connection has been chained Format:

AT+ TCPLK<CR>

+ok=<sta><CR>< LF ><CR>< LF >

Parameters:

sta.: Returns whether TCP builds a chain, such as

on, indicating that the chain has been built

off, indicating that there is no chain built.

3.2.2.2.19 AT+TCPDIS

Function: Link/Disconnect TCP (valid only in TCP Client)

Содержание CX-WIFI-2NET






























































































Результаты поиска

Содержание CX-WIFI-2NET

Отзывы:

Похожие инструкции для CX-WIFI-2NET

Бренды по названию

Популярные бренды

Coolmay CX-WIFI-2NET, Руководство пользователя

Результаты поиска

Содержание CX-WIFI-2NET

Отзывы:

Похожие инструкции для CX-WIFI-2NET

Бренды по названию

Популярные бренды