Coolmay CX-WIFI-2NET Скачать руководство пользователя страница 88

Страница: 88 / 93

Shenzhen Coolmay Technology Co.,Ltd

CX-WIFI-2NET module user manual

www.coolmay.com

Page

, Total 93 pages

Appendix A: FAQ and Answers

Question 1: Two CX-WIFI-2NET modules are interconnected, and

the TCP protocol is used as a transparent serial port. How to set it?

As belowing picture shown,
1# module as AP, the default setting can be.
The 2# module is used as the STA, the WAN port address is

dynamically obtained, or statically set, such as set to 10.10.100.100.

The TCP protocol of the 2# module is set as follows: TCP Client, port

8899 is unchanged, and the IP address is the LAN IP address of the 1#
module (ie AP): 10.10.100.254.

When the module is set to STA, its WIFI port is the WAN port, and

the WAN address must not be on the same network segment as the
LAN address, so the LAN IP of the 2# module needs to be changed, as
shown in Figure 10.10.99.254.

Question 2

：

CX-WIFI-2NET module LAN IP settings, WAN IP settings

Where are they set?

The LAN IP is set in the “Wireless Access Point Settings” page as

shown below: The WAN IP is set in the “Wireless Terminal Interface
Settings” page as follows:

Содержание CX-WIFI-2NET






























































































Результаты поиска

Содержание CX-WIFI-2NET

Отзывы:

Похожие инструкции для CX-WIFI-2NET

Бренды по названию

Популярные бренды

Coolmay CX-WIFI-2NET, Руководство пользователя

Результаты поиска

Содержание CX-WIFI-2NET

Отзывы:

Похожие инструкции для CX-WIFI-2NET

Бренды по названию

Популярные бренды