Continental Refrigerator RightViu Скачать руководство пользователя | Manualshive

Страница: 24 / 52

background image

24

4

Mount the following using the M5

countersunk-head screws

›

Housing (1)

›

Base plate (3)

›

Ball holder G20 (4)

4

3

5

Guide the connection cable for the

radar sensor (12) through the cable gland

and the lock nut (18).

6

Guide the connection cable for the

radar sensor (12) through the rubber sleeve

(19) so that the cable gland (18) is covered.

NOTE

Pull the connection cable for the radar sensor (12) only as far through as necessary to ensure the cable is completely inside the radar

housing. Ensure that the connection cable for the radar sensor (12) is between the cable gland (18) and the inlet on the passenger

door, and that there is sufficient cable. If there is not, then the vehicle mirror may not be able to be folded in if necessary.

12

18

19

ASSEMBLE THE RADAR HOUSING

«
...
22
23
24
25
26
...
»

Содержание RightViu





















































Отзывы:

Нет отзывов

Похожие инструкции для RightViu

Бренд: SAGEMCOM Страницы: 120

Бренд: Eton Страницы: 18

Бренд: Xoro Страницы: 32

Бренд: SpotterRF Страницы: 2

Бренд: Kitsound Страницы: 8

Бренд: Ocean Digital Страницы: 2

Бренд: UNIMO Technology Страницы: 10

Busch-AudioWorld 8217 U-101

Бренд: Busch-Jaeger Страницы: 119

Бренд: Connect Systems Страницы: 13

Бренд: Zte Страницы: 29

Бренд: Roadstar Страницы: 11

Бренд: SAFETY WORKS Страницы: 2

SP3520 VHF GMDSS

Бренд: Sailor Страницы: 44

Бренд: K40 Страницы: 6

Бренд: Hama Страницы: 64

Бренд: Simrad Страницы: 24

Бренд: Midland Страницы: 20

ALAN 8001S EURO

Бренд: Midland Страницы: 92

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды