manualshive.com logo in svg

Continental Refrigerator RightViu, Инструкция по монтажу

Поделиться
Скачать
Continental Refrigerator RightViu Скачать руководство пользователя страница 36

36

DANGER!

Mortal danger due to unauthorised restart!
If power supplies have been switched off and are switched on again without authorisation, 
this poses a mortal danger to workers.
- Always secure power supplies against restart after they are turned off.

DANGER!

Do not bend, pinch, or roll over the cables or allow them to come into contact with heat 
sources or sharp edges.

DANGER!

If insulation is damaged, immediately unplug the power supply. Never allow liquids to 
penetrate the system.

DANGER!

Mortal danger from electric current!
Touching live parts poses a mortal danger from electric shock.

DANGER!

Mortal danger due to stored charge!
Electrical charges may be stored in electronic components. These charges may remain 
even after:
- the power supply has been switched off and unplugged. Coming into contact with such 
components may result in severe or deadly injuries.
- Only allow trained electricians to complete work on electronic components.
- Before working on electronic components: Unplug components from the power supply. 
Wait 10 minutes so that capacitors can discharge fully.

ECU INSTALLATION

Содержание RightViu





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды