manualshive.com logo in svg

Continental Refrigerator RightViu, Инструкция по монтажу

Поделиться
Скачать
Continental Refrigerator RightViu Скачать руководство пользователя страница 17

17

WARNING!

Danger due to improper assembly!
Improper assembly may result in personal injury, property damage or environmental 
damage. 
The device must be installed according to the assembly manual.

WARNING!

Mortal danger due to improper work!
Please observe the safety instructions issued by the vehicle manufacturer and the vehicle 
industry as a whole, and observe technical installation requirements.

DANGER!

Mortal danger due to improper work!
Installation and commissioning errors may result in life-threatening injuries and significant 
property damage.
=> Installation, assembly and electrical connections may only be carried out by trained 
technicians and only in accordance with the information in this assembly manual. 

CAUTION!

Danger of injury on sharp edges and pointed corners! Sharp edges and pointed corners 
of components may cause cuts and abrasion on the skin.

-

In general, observe the vehicle manufacturer's regulations when carrying out all repairs 
and servicing work.

Safety instructions

INSTALLATION AND ASSEMBLY

Содержание RightViu





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды