manualshive.com logo in svg

Continental Refrigerator RightViu, Инструкция по монтажу

Поделиться
Скачать
Continental Refrigerator RightViu Скачать руководство пользователя страница 20

20

B

   Mounting the pivoted joint

90°

180°

112,5°

135°

157,5°

The following adjustment angles are possible:

      90°                        112.5°                         135°                         157.5°                          180°

The pivoted joint can be adjusted in steps of 22.5° between 90° and 180° pre-inclination. 

The pivoted joint is secured by a stainless steel pin in these positions. This is pressed in on 

delivery of RightViu.

The basic alignment of the pivoted joint is designed in such a way that when the plate is 

attached horizontally at the base of the mirror with the long side in direction of movement, 

the centre position of the joint is inclined 45° to the rear and 45° down.

Rotation of the joint in relation to the plate can be changed as required by turning the drilling 

template for the 4 x M4 threaded holes.

NOTE

All the tightening torques required to 

mount RightViu can be found in the 

tightening torques chapter in the 

annex.

PREPARATORY WORK

Содержание RightViu





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды