Contec SCP-8550-LLV Скачать руководство пользователя

Страница: 18 / 78

3. Hardware Installation

SCP-8550-LLV

Hardware Installation

This chapter provides information on how to use the jumpers and connectors on the SCP-8550-LLV in
order to set up a workable system.

Installation procedure

(1)

Confirm the power supply is off.

(2)

Install the processor with correct orientation.

(3)

Mount the Heat sink on the top of the processor. (The heat sink with a fan connects a fan cable to
the fan connector on a board.)

(4)

Insert the DDR DRAM module with correct orientation.

(5)

Confirm CPU board into to CompactPCI back plane.

(6)

Insert all external cables. (Keyboard, Mouse, LAN, etc.)

(7)

Prepare a CRT monitor for CMOS setup.

(8)

Turn on the power.

(9)

Enter the BIOS setup mode by pressing ‘F2’ key during boot up.

(10) Use the “Load BIOS Optimal Defaults” feature.

(11) Configure the

Peripheral Setup

and the

Standard Setup

correctly.

CAUTION

The CMOS memory may be in an undefined state at power-on after a period of no battery backup.

Содержание SCP-8550-LLV















































































Результаты поиска

Содержание SCP-8550-LLV

Отзывы:

Похожие инструкции для SCP-8550-LLV

Бренды по названию

Популярные бренды

Contec SCP-8550-LLV, Руководство пользователя

Результаты поиска

Содержание SCP-8550-LLV

Отзывы:

Похожие инструкции для SCP-8550-LLV

Бренды по названию

Популярные бренды