Contec CONPROSYS CPS-PC341MB-ADSC1-9201 Скачать руководство пользователя страница 26

Страница: 26 / 84

—

Product Nomenclature and Function

—

CPS-PC341MB-ADSC1-9201 Reference Manual (Hardware)

—

LED Indicator

Status of the product is indicated by of LED ON/OFF and flashing.
The meaning of each LED is described below.

Color and Description

LED

Color

Display

Description

PWR

Green ON

Power has been supplied.

OFF

Power has not been supplied.

Yellow Flashing

It flashes at the SD access.

OFF

It indicates there is no SD access.

ST1

Green -

Refer to the Reference Manual (Software).

ST2

Red

Refer to the Reference Manual (Software).

TX(COM A)

Yellow Flashing

It flashes upon transmitting data by the RS-422A/485.

OFF

It indicates there is no data transmission by RS-422A/485.

RX(COM A)

Yellow Flashing

It flashes upon receiving data by the RS-422A/485.

OFF

It indicates there is no data reception by RS-422A/485.

TX(COM B)

Yellow Flashing

It flashes upon transmitting data by the RS-232C.

OFF

It indicates there is no data transmission by the RS-232C.

RX(COM B)

Yellow Flashing

It flashes upon transmitting data by the RS-232C.

OFF

It indicates there is no data transmission by the RS-232C.

DI0 - DI3

Yellow ON

It lights up when there is inputting.

OFF

It indicates there is no inputting.

DO0 - DO1

Yellow ON

It lights up when there is outputting.

OFF

It indicates there is no outputting.

AI0 - AI1

Yellow ON

It lights up upon measuring.

OFF

It indicates there is no measuring.

Resets switch

This resets the product.

Содержание CONPROSYS CPS-PC341MB-ADSC1-9201





















































































Результаты поиска

Содержание CONPROSYS CPS-PC341MB-ADSC1-9201

Отзывы:

Похожие инструкции для CONPROSYS CPS-PC341MB-ADSC1-9201

Бренды по названию

Популярные бренды

Contec CONPROSYS CPS-PC341MB-ADSC1-9201, Справочное руководство

Результаты поиска

Содержание CONPROSYS CPS-PC341MB-ADSC1-9201

Отзывы:

Похожие инструкции для CONPROSYS CPS-PC341MB-ADSC1-9201

Бренды по названию

Популярные бренды