Contec CONPROSYS CPS-PC341MB-ADSC1-9201 Скачать руководство пользователя страница 65

Страница: 65 / 84

—

Installation

—

CPS-PC341MB-ADSC1-9201 Reference Manual (Hardware)

—

Example of connecting to the LED

The corresponding LED lights up when you output "1" into the appropriate bit.
The corresponding LED turns off when you output "0" into the appropriate bit.

Connecting to an external device

Connecting the output to the sink output acceptable input

Connecting the output to the source acceptable input

CAUTION



Removing the connector plug by grasping the cable can break the wire. Always grasp the
connector to remove it.



Tightening torque of the supplied connector is described below.
DEGSON : 0.19 N·m, PHOENIX CONTACT, PTR MESSTECHNIK : 0.25 N·m



For wiring, strip off approximately 7mm (plus or minus 0.5mm) of the covered part of a cable
to connect with the connector.



About a caution mark on the product: Please use copper wires that tolerate the
temperature of 75 °C and higher.

Output pin (+)

LED

5.1kΩ

Output pin (-)

External power

supply

12 - 24 VDC

is P

This Product

Output pin(-)

Output pin(+)

Sink output

acceptable input

External

power supply

Source output

acceptable input

This Product

Output pin(+)

Output pin(-)

External

power supply

Содержание CONPROSYS CPS-PC341MB-ADSC1-9201





















































































Результаты поиска

Содержание CONPROSYS CPS-PC341MB-ADSC1-9201

Отзывы:

Похожие инструкции для CONPROSYS CPS-PC341MB-ADSC1-9201

Бренды по названию

Популярные бренды

Contec CONPROSYS CPS-PC341MB-ADSC1-9201, Справочное руководство

Результаты поиска

Содержание CONPROSYS CPS-PC341MB-ADSC1-9201

Отзывы:

Похожие инструкции для CONPROSYS CPS-PC341MB-ADSC1-9201

Бренды по названию

Популярные бренды