CONQUEST PB120E, Руководство оператора

Страница: 10 / 46

-
8
2 Safety rod
 Fold the safety rod for the high empty-
ing up and insert it into the holder (se-
cured).
The batteries can only be exchanged as a
set. The exchange has to be performed by
trained personnel.
 Due to the heavy weight (450 kg), the
batteries must be exchanged using a
crane.
Note : The cross strut must be un-
screwed prior to replacing the battery.
 When removing the battery, disconnect
the negative terminal wire first.
 Fasten the crane chains in the four eye-
lets of the battery set and carefully lift
out the batteries.

DANGER
Risk of injury!
 Always apply the safety rod when the
waste container is raised.
 Perform the safeguarding only from
outside the hazard zone.
1 Holder of safety rod
2 Brake fluid container
3 Closing head
 Move up the waste container and se-
cure it by means of the safety rod, see
Chapter "Emptying the waste contain-
er"
 Check if the there is enough brake fluid
in the brake fluid reservoir.
Note
The filling level has to be between Min.
and Max.
 If necessary, refill DOT brake fluid cur-
rently commercially available.
NOTICE
The waste container must not be raised.
 Open engine cover.
1 Hydraulic oil tank
2 Looking glass
3 Screw cap, oil fill opening
 Check hydraulic oil level in the looking
glass.
–
The oil level must lie between “MIN“
and “MAX“ marking.
–
Add hydraulic oil if the oil level is below
the "MIN" marking.
 Loosen the closing cap of the oil filling
opening.
 Clean the filling area.
 Refill hydraulic oil.
Oil grade: see Technical Data
 Replace and tighten the closing cap of
the oil filling opening.
 Lock parking brake.

Start the motor.
Maintenance of the hydraulic system is
only to be carried out by ISAL Customer
Service.

Check all hydraulic hoses and connec-
tions and ensure that they are leak-
proof.
 Sit on the driver's seat.
 Bring the direction selector switch into
the middle position.
 Turn the ignition key to position "I".
 Raise the waste container up to the
end-position.
 Turn ignition key to "0" and remove it.
 Lock parking brake.
 Use the safety bar for emptying from a
height.
 Remove belts or cords from roller
brush.
 Remove the safety bar.
 Insert the ignition key into the ignition
switch.
 Turn the ignition key to position "I".
 Lower the waste container up to the
end-position.
 Turn ignition key to "0" and remove it.
1 Key
2 Side panels
 Drive the waste container up and sup-
port it with the safety rod.
 Open the side covers using a key.
1 Holding bow
2 Wing nut
3 Side seal
 Unscrew the wing nuts.
 Remove the retaining clamp.
 Flip the side seal out.
 Uncscrew the retaining screw of the
roller brush intake, and swing the intake
to the outside.
 Pull out roller brush.
Installation position of roller brush in direc-
tion of travel (top view)
Note: When installing the new roller brush,
ensure correct positioning of the bristle as-
sembly.
 Install new roller brush. The nuts of the
roller brush must be inserted on the
notches of the opposite crank.
Note: Once the new roller brush has been
installed, the sweeping track must readjust-
ed.
Note : The sweeping track is factory-set to
80 mm; it is steplessly adjustable if the
brush roller wears down.
 Check tyre pressure.
 Switch off suction blower.
Replace batteries
Checking the brake fluid level and
topping up brake fluid
Check hydraulic oil level and refill
hydraulic oil
Check hydraulic unit
Checking roller brush
Replacing roller brush
Check and adjust roller brush sweeping
track
22 EN