background image

-

5

Loosen parking brake; press brake
pedal at the same time.

Activate the parking brake; press brake
pedal at the same time.

Park the sweeper on an even surface.

Remove ignition key.

Lock parking brake.

Check battery charging status; charge
batteries it if required (see Chapter
"Charging the batteries").

Check the sweeping roller and the side
brush for wear and wrapped belts.

Check the wheels for tied up belts.

Check function of all operator control el-
ements.

Check appliance for damages.

Clean the dust filter with the filter clean-
ing button.

Note:

 For description, see section on Care 

and maintenance.

Please observe the following warning notes 
when handling batteries:

Danger

Risk of explosion! Do not put tools or similar 
on the battery, i.e. on the terminal poles
and cell connectors.

Danger

Risk of injury! Ensure that wounds never 
come into contact with lead. Always clean 
your hands after having worked with batter-
ies.

Danger

Risk of fire and explosion!

Smoking and naked flames are strictly
prohibited.

Rooms where batteries are charged
must have good ventilation because
highly explosive gas is emitted during
charging.

Danger

Danger of causticization!

Rinse thoroughly with lots of clear water 
if acid gets into the eye or comes in con-
tact with the skin.

Then consult a doctor immediately.

Wash off the acid If it comes in contact
with the clothes.

CAUTION

Charge the batteries before commissioning 
the machine. 

DANGER

Risk of injury! Comply with safety regula-
tions on the handling of batteries. Observe
the directions provided by the manufacturer 
of the charger.
Please read and follow the included operat-
ing instructions by the battery manufacturer 
and follow them.
Charge the battery only with an appropriate 
charger.

Danger

Danger of chemical burns. Adding water to
the battery in its discharged state can
cause the acid to leak! Use safety glasses
while handling battery acid and follow the
safety instructions to avoid personal injury
or damage to clothes. Should the acid
spray on to the skin or clothes, rinse imme-
diately with lots of water.

CAUTION

Risk of damage. Use only distilled or desal-
inated water (VDE 0510) for filling the bat-
tery. Do not add any substances (so-called
performance improving agents), else war-
ranty claims will not be entertained.

The use of other batteries and chargers is 
not recommended and may only take place 
after consulting with ISAL customer ser-
vice.

Pull the battery plug from the machine
and connect it to the plug of the charg-
er.

Connect the plug of the charger to a
proper socket of 16 A, the charger will
charge automatically.

Always keep both motor covers open
during the charging process.

Note:

 When the batteries are charged,

first remove the charger from the mains
and then disconnect it from the batter-
ies.

CAUTION

Be sure to observe the battery manufactur-
er’s instructions and then act accordingly.

Display of the battery capacity in the
green range:
Battery is charged.

Display of the battery capacity in the
yellow range:
Battery is halfway discharged.

Display of the battery capacity in the red
range:
Battery is almost discharged. The
sweeping mode will be shortly switched
off automatically.

Indicator lamp glows red
Battery is discharged. The sweeping
mode will be terminated automatically
(the sweeping aggregates cannot be
taken into operation until the battery is
charged).

Drive the machine directly to the charg-
ing station; avoid any steep gradients in
the process.

Charge battery.

1 Lever for seat adjustment
2 Driver seat

Pull seat adjustment lever outwards.

Before Startup

Lock/ release parking brake

Start up

General notes

Inspection and maintenance work

Daily before starting operations

Safety notes regarding the batteries

Observe the directions on the 
battery, in the instructions for 
use and in the vehicle operat-
ing instructions!
Wear an eye shield!

Keep away children from acid 
and batteries!

Risk of explosion!

Fire, sparks, open light, and 
smoking not allowed!

Danger of causticization!

First aid!

Warning note!

Disposal!

Do not throw the battery in the 
dustbin!

Beware of dangerous electrical 
current!

Charge the batteries

Recommended batteries, chargers

Order number

Battery pack

 36 V, 

360 Ah, (in the trough, 
low maintenance) *

6.654-282.0

Charger

 36 V, 50 A

6.654-283.0

* Appliance requires 1 battery pack

Check fluid level in the battery and 
adjust if required

Check charging status of battery

Operation

Adjusting driver's seat

19

EN

Содержание PB120E















































Отзывы: