manualshive.com logo in svg

Conductix-Wampfler Safe-Lec 2, Руководство пользователя

Поделиться
Скачать
Conductix-Wampfler Safe-Lec 2 Скачать руководство пользователя страница 20

20

          

Safe-Lec 2 Conductor Bar Manual

SECTION 9 - END CAP ONTO CONDUCTOR BAR ASSEMBLY

Galvanized Steel and Copper Conductor Bar Installation

Install end caps onto galvanized steel and copper conductor bars. See 

Figure 20-1.

Tools Needed

•  10mm A/F open ended wrench

Installation

1.  Fit bolt into joint plate (ensure tab captivates the head on the set screw).
2.  Place bolt and joint plate assembly into conductor bar.
3.  Place end cover clamp, washer, and nut over bolt and joint plate assemblies (ensure end cover clamp is flush with conductor bar 

face).

4.  Tighten nut to a recommended torque of 8 Nm (5-6 ft-lbs).
5.  Push end cover over assembly (ensure bolt is located in point “A” on end cover).

NOTE:

Wings on Tab to
face upwards.

This face to be flush
with conductor face.

Figure 20-1

1.  Nut
2.  Washer
3.  End Cover Clamp

4.  Bolt
5.  Joint Plate
6.  End Cover

3

2

4

5

6

A

1

Содержание Safe-Lec 2









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды