manualshive.com logo in svg

Conductix-Wampfler Safe-Lec 2, Руководство пользователя

Поделиться
Скачать
Conductix-Wampfler Safe-Lec 2 Скачать руководство пользователя страница 13

Safe-Lec 2 Conductor Bar Manual

         

13

 

SECTION 3 - SUPPORT BRACKETS

Support Bracket Installation

1.  Locate and secure support brackets at the recommended spacing. See 

Figure 13-1.

NOTE

•  Locate support brackets at a spacing that is divisible into the conductor bar lengths.  This will ensure that the joint positions do 

not interfere with the support brackets.

2.  Observe all alignment tolerances. See 

Figure 13-1.

 

»

Datum height

 

»

Maximum allowable deviation from datum 5.0mm (+3/16”).

Advantage of Factory-Made Brackets

Safe-Lec 2 Hanger Support Brackets come complete with all necessary mounting holes for easy installation of hangers via slide in slots 
or holes.

Alignment tolerance over 4.5 
meters (14.75 ft) in runway 
length:  ± 5.0 mm  (± 3/16”)

59”

 Max

59”

 Max

Bracket slots: 9mm wide.  Will 
accommodate 4 anchors on 
43mm centers

Straight datum line running the 
length of the runway system

Содержание Safe-Lec 2









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды