background image

MN5-1060-XXX

iii

Revision 1

XTRT-400C Operation and Installation Manual

About this manual

This manual provides operators and technicians with a set of 
tools for operating and maintaining the Rack Mount Family of 
Xicom Power Amplifiers. 

This Prefix contains a Table of Contents that applies to the 
entire manual and a Record of Changes page that applies only 
to this Prefix.

Each Chapter and Appendix has its own part Number, Revision 
Level, Record of Changes page, Table of Contents, List of 
Figures, and List of Tables.

Chapter One—

Provides an overview of the manual; delineates 

who should use the manual; how to contact Xicom Technology.

Chapter Two—

Describes safety information that pertains to 

Xicom Technology products. It also provides information about 
Warnings, Cautions and Notes that are found throughout the 
manual.

Chapter Three—

Provides general installation information, 

communication interface switch settings and cable pinouts.

Chapter Four—

Provides the operating instructions for the power 

amplifier.

Chapter Five—

Provides communication protocols used with 

Xicom Technology power amplifiers.

Chapter Six—

Describes the preventive maintenance 

requirements for Xicom Technology power amplifiers

Chapter Seven—

Provides information regarding service and 

repair of Xicom Technology power amplifiers, including 
instrucitons on obtaining RMA (Return Maintenance 
Authorization) Numbers.

Chapter Eight—

Provides operational instructions at the system 

level.

List of Abbreviations, Acronyms, and CE Symbols—

Lists the 

abbreviatons, acronyms, and CE symbols that may be found in 
Xicom Technology documentation.

Appendices—

The Appendices provide operators and 

technicians with information and specifications that are specific 
to their particular version of Xicom Technology Amplifier.

 

EAR EXPORT CONTROLLED:  The information contained in this Manual refers or relates to a product that is subject 

to the U.S. Export Administration Regulations (EAR).  Transfer of data herein by any means to a Foreign Person, 

whether in the U.S. or abroad, may require an export license from the U.S. Department of Commerce.

Содержание XTRT-400C


































































































































































































Отзывы: