Comtech EF Data Vipersat SLM-5650A Скачать руководство пользователя страница 303 | Manualshive

Страница: 303 / 516

background image

SLM-5650A Satellite Modem

Revision 10

Appendix C

C–9

MN-SLM-5650A

In order to provide a robust set of LDPC codes with varying degrees of latency, the SLM-5650A
has implemented three different block sizes:

•

The Ultra Low Latency (ULL) code provides the lowest latency, but worst performance of
the three block sizes. This code is available in the data rate range from 32 kbps to 2 Mbps
and is compatible with the CDM-625 ULL code.

•

The Low Latency (LL) code provides modest latency and performance over the data rate
range of 32 kbps to 5 Mbps.

•

The High Performance (HP) code provides the best performance but worst latency. This
code is available from 32 kbps up to 69 Mbps depending on MODCOD. The HP code is
compatible with the CDM-625 LDPC code.

See

Appendix B. OPERATIONAL REFERENCES

for more details on the data rate and symbol

rate ranges supported in each code.

«
...
301
302
303
304
305
...
»

Содержание Vipersat SLM-5650A





































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Vipersat SLM-5650A

Бренд: FALCOM Страницы: 22

Бренд: Edimax Страницы: 44

Бренд: Jizhuo Technology Страницы: 13

Бренд: Belkin Страницы: 4

Бренд: Four-Faith Страницы: 22

Бренд: Fritz! Страницы: 2

Бренд: O2 Страницы: 48

Бренд: 3Jtech Страницы: 50

Бренд: Embedded Planet Страницы: 26

SURFboard SBG6950AC2

Бренд: CommScope Страницы: 64

Бренд: Zhone Страницы: 2

Бренд: Zte Страницы: 2

Бренд: Abocom Страницы: 14

Ripwave 40-00097-00

Бренд: Navini Networks Страницы: 41

Бренд: Feasycom Страницы: 6

Бренд: Wavenet Technology Страницы: 35

Бренд: Patton electronics Страницы: 15

Бренд: Conexant Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды