Comtech EF Data Vipersat SLM-5650A Скачать руководство пользователя страница 147

Страница: 147 / 516

SLM-5650A Satellite Modem

Revision 10

Front Panel Operation

7–41

MN-SLM-5650A

7.2.4.3 (Monitor:) Rx-Params

Fc=+05917 RSL<-60.0 dBm BERT=N/A
Buf=000% Eb/No=Loss BER <1.0E-12 (



This

read-only

screen monitors the following Rx operating parameters:

•

displays the received carrier frequency offset in Hz. The range is the same as the

acquisition range of the modem (60 kHz).

•

RSL

displays the signal level of the received carrier in dBm. The range supported is

(+15) to (-60) dBm.

•

BERT

displays the measured BER. This requires that the modem be set to

Test

mode for

Rx. If a Fireberd is supplying a data pattern, only the

Test

mode for the Rx needs to be

turned on. The Fireberd data pattern and the modems’ data patterns must match to work
properly.

•

Buf

displays the buffer fill status as a percentage.

•

Eb/No

displays the estimated Eb/No of the received carrier. The range is threshold to 20

dB Eb/No.

•

BER

displays the estimated BER based on the demodulator’s measurement of the carrier

to noise.

The difference between BERT and BER is that BERT is measured when
the Test mode is turned ON, whereas BER is estimated in the
demodulator.

Press

[ENT]

[CLR]

to return to the previous menu.

7.2.4.4 (Monitor:) CnC (DoubleTalk® Carrier-in-Carrier®)

CnC: Delay=000,005uS FreqOff=008.7kHz

Eb/No=Loss Ratio<-10dB (E)

This

read-only

screen updates once every second. If enabled and locked, this screen monitors

the CnC performance data:

•

Delay

displays the current search delay value.

•

FreqOff

displays the current frequency offset between the outbound interferer and the

desired inbound.

•

Eb/No

displays the estimated Eb/No of the received carrier. The range is threshold to 20

dB Eb/No.

•

Ratio

displays the ratio of outbound interferer power to desired inbound power. The

range is ±10 dB.

Press

[ENT]

[CLR]

to return to the previous menu.

Содержание Vipersat SLM-5650A





































































































































































































































































































































































































































































































































Результаты поиска

Содержание Vipersat SLM-5650A

Отзывы:

Похожие инструкции для Vipersat SLM-5650A

Бренды по названию

Популярные бренды

Comtech EF Data Vipersat SLM-5650A, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Vipersat SLM-5650A

Отзывы:

Похожие инструкции для Vipersat SLM-5650A

Бренды по названию

Популярные бренды