Comtech EF Data Vipersat SLM-5650A Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 516

background image

SLM-5650A Satellite Modem

Revision 10

Preface

i

MN-SLM-5650A

PREFACE

About this Manual

This manual describes the installation and operation for the Comtech EF Data SLM-5650A
Satellite Modem. This is a document intended for the persons responsible for the operation and
maintenance of the SLM-5650A.

Conventions and References

Patents and Trademarks

See all of Comtech EF Data's Patents and Patents Pending at http://patents.comtechefdata.com.

Comtech EF Data acknowledges that all trademarks are the property of the trademark owners.

•

DoubleTalk

®

is licensed from “Raytheon Applied Signal Technology”.

•

DoubleTalk

®

is a registered trademark of “Raytheon Applied Signal Technology”.

•

Carrier-in-Carrier

®

is a registered trademark of Comtech EF Data.

Related Documents

The following documents are referenced in this manual:

•

Department of Defense (DOD) MIL-STD-188-114A, Electrical Characteristics of Digital
Interface Circuits

•

Department of Defense (DOD) MIL-STD-188-165A, Interoperability and Performance
Standards for SHF Satellite Communications PSK Modems (FDMA Operation) (dated
November 2005)

•

INTELSAT Earth Station Standards IESS-308, -309, -310, and -315

•

EUTELSAT SMS

«
...
19
20
21
22
23
...
»

Содержание Vipersat SLM-5650A





































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Vipersat SLM-5650A

Бренд: Radyne Страницы: 11

Бренд: NextNet Страницы: 26

Бренд: H3C Страницы: 54

MA02-AAC 2220 Series

Бренд: Ebyte Страницы: 41

Бренд: D-Link Страницы: 8

MicroLink-HM 101-0029

Бренд: Microflex Страницы: 17

Бренд: Four-Faith Страницы: 34

Бренд: Ebyte Страницы: 31

U.S. Robotics 56K Professional Message

Бренд: 3Com Страницы: 37

Бренд: AIS Страницы: 14

Бренд: HSP Страницы: 8

Бренд: Zte Страницы: 52

Бренд: Zte Страницы: 27

Бренд: RACOM Страницы: 127

Бренд: Datum Systems Страницы: 124

Бренд: Radyne Страницы: 214

CheetahModem ACM 120

Бренд: Accton Technology Страницы: 54

Бренд: NetComm Wireless Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды