Comtech EF Data Vipersat SLM-5650A Скачать руководство пользователя страница 116

Страница: 116 / 516

SLM-5650A Satellite Modem

Revision 10

Front Panel Operation

7–10

MN-SLM-5650A

(CONFIG:) Tx



Mod

Mod: FEC:VIT Type:QPSK Rate:1/2

RS:Off Diff:On Scram:OM-73 (



Use the



arrow keys to select

FEC

Type

Rate

Diff

, or

Scram

. Press

[ENT]

. For any

option, use the



arrow keys to scroll through the available settings. Select your setting. Press

[ENT]

to finish.

Option

Setting

FEC

Standard settings:

•

VIT (Viterbi) – K=7 convolutional encoder.

•

NONE – Uncoded.

Optional settings:

•

TURBO – Turbo Product Code, which is a block code.

•

SEQ – Sequential Encoder/Decoder.

•

ULL – Ultra Low Latency LDPC

•

LL – Low Latency LDPC

•

HP – High Performance LDPC

Type

(Modulation)

Standard settings:

•

BPSK – Bi Phase Shift Keying.

•

QPSK – Quadrature Phase Shift Keying.

•

OQPSK – Offset Quadrature Phase Shift Keying.

Optional settings:

•

8PSK – 8 Phase Shift Keying.

•

8QAM – 8 Quadrature Amplitude Modulation

•

16QAM – 16 Quadrature Amplitude Modulation.

Rate

•

Viterbi – 1/2; 2/3; 3/4; 5/6; 7/8

•

Uncoded – 1/1

•

Turbo – 5/16; 3/4; 7/8; 17/18; 21/44

•

Sequential – 1/2; 3/4; 7/8

•

ULL – 1/2; 2/3; 3/4

•

LL – .378; .451; .541; 1/2; 2/3; 3/4; 7/8

•

HP – 1/2; 2/3; 3/4

Reed-Solomon Encoder: On or Off

Diff

Differential Encoder: On or Off

Scram

Scrambling (for energy dispersal):

•

V.35 – ITU standard.

•

MOD-V.35 (Modified V.35) – Comtech EF Data Closed Network with Reed- Solomon

compatible .

•

IBS – Used for IESS-309 operation.

•

Turbo – Synchronous scrambler synchronized to the Turbo block.

•

OM73 – Linkabit OM-73 modem compatibility mode.

•

Synch – Synchronous scrambler synchronized to the Reed-Solomon.

•

Off – Scrambling is disabled.

When changing modulation type, the data rate must be set to a rate supported by the modulation

type or the change to the modulation type will not be allowed. Some choices will only be visible if

the modem is set to a compatible mode, or if an option is installed or enabled.

Содержание Vipersat SLM-5650A





































































































































































































































































































































































































































































































































Результаты поиска

Содержание Vipersat SLM-5650A

Отзывы:

Похожие инструкции для Vipersat SLM-5650A

Бренды по названию

Популярные бренды

Comtech EF Data Vipersat SLM-5650A, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Vipersat SLM-5650A

Отзывы:

Похожие инструкции для Vipersat SLM-5650A

Бренды по названию

Популярные бренды