Comrex BRIC-Link Скачать руководство пользователя страница 19

Страница: 19 / 95

iV.

USING THE DEVICE MANAGER PROGRAM

Firmware updates for the BRIC-Link should be handled using Comrex

Device Manager

, a Windows- and MAC

OS-executable program that can be downloaded from the Comrex website.

Device Manager

can also be used for

license installation and IP configuration.

Please note: In order to configure a BRIC-Link unit for the first time (without knowing the unit’s IP address),

Device

Manager

must be run on a computer located on the same network (e.g. physical LAN connection) as the unit itself.

If this is not possible, an Ethernet crossover connection between the BRIC-Link and a computer should be used for
configuration.

Figure 6

deVice manager

As shown in

Figure

, running the

Device Manager

and clicking the “

Scan

” button will produce a list of all Comrex

devices found on the LAN. If the default password has changed,

Device Manager

will prompt for the password to

BRIC-Link after the scan.

Figure 6

shows the four tabs that appear on the right-hand pane after

Device Manager

has logged in. The fourth

tab is labelled

Web Configuration

. This will open a simplified setup interface on the BRIC-Link called

Toolbox

. The

Toolbox

interface allows for configuration of several options including the Ethernet port. Log in to

Toolbox

with a

username (any) and password (default =

comrex

) to enter the

Toolbox

Once logged into

Toolbox

, choose the

Network/Admin/CrossLock

option and then choose

Set up Ethernet

. Choose

the Ethernet port that appears in the list, which will look like

Figure 7

Содержание BRIC-Link
































































































Результаты поиска

Содержание BRIC-Link

Отзывы:

Похожие инструкции для BRIC-Link

Бренды по названию

Популярные бренды

Comrex BRIC-Link, Руководство по эксплуатации продукта

Результаты поиска

Содержание BRIC-Link

Отзывы:

Похожие инструкции для BRIC-Link

Бренды по названию

Популярные бренды