Comrex BRIC-Link Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 95

Comrex BRIC-Link Скачать руководство пользователя страница 47

VIII.

MAKING SWITCHBOARD CONNECTIONS ON BRIC-LINK

This section describes the procedure of making and receiving connections on BRIC-Link via the Comrex Switchboard
server. This is the easiest way, but not the only way, to make BRIC-Link connections. Before connections are made this
way, you must set up and configure a Switchboard Account as described in

Section X

.

If you don’t want to use the Switchboard server to make connections, skip this section and go to

Section IX

, Making

Manual CrossLock Connections.

Note:

BRIC-Link requires a Switchboard Traversal Server License to be used with

Switchboard.

Switchboard Connections can be made with or without the CrossLock protection layer. Note that this choice affects
which IP ports are used for connections, so there are implications concerning firewalls and routers.

When Switchboard is used, the choice of “peers” to connect to appears in a dynamic list, as shown in

Figure 30

. Any peer

showing a “gear” icon is a connectible codec. If that gear is green, the far-end is available for incoming connections.

By selecting a Switchboard peer and clicking the edit “pencil’ icon on the right side, you can change several important
aspects of the Switchboard connection:

1.

Use CrossLock

- Determine whether the connection will be made over the CrossLock Layer and port arrangement,

or over the legacy BRIC Normal protocol and port arrangement.

2.

Connection Password

- This adds an extra layer of security to the connection. This is a password that has been

programmed into the receiving codec, and will be required on the outbound side for proper connection. Since
Switchboard provides its own connection filtering, passwords are not normally used in this mode.

3.

Profile

- Choose one of the factory-supplied or custom built profiles for this connection. This defines encoders

used in both directions, along with a long list of other parameters. See the Profile section in the setup section for
more. If none is specified, the profile designated as default will be used.

4.

Backup/Fall Forward settings

- Described in the section “Making Manual Connections”.

FIgure 30

SwItchboard peer remote

47

«
...
45
46
47
48
49
...
»

Содержание BRIC-Link
































































































Отзывы:

Нет отзывов