manualshive.com logo in svg

Comrex BRIC-Link, Руководство по эксплуатации продукта, Страница: 36 / 95

Поделиться
Скачать
Comrex BRIC-Link Скачать руководство пользователя страница 36

36

Switchboard Address

 - IP address of the Switchboard server.

Secure

 - Enables secure connections to Switchboard Server. This is enabled by default.

Static Crosslock Peers

 - When using CrossLock without Switchboard, remote peers can be managed in this list.

CROSSLOCK VPN

Enable

 - This option enables the Crosslock VPN added reliability layer to connect to remote units. (See 

Making 

BRIC-Link Connections Using Crosslock 

on 

Page 45 

for more information on using the Crosslock VPN.) 

Retransmit Delay

 - This section allows the selection of additional delay for the retransmission of lost packets when 

calculating auto-delay targets. The 2xRTT setting is selected by default.

Redundant Transmission

 - When calculating auto-delay target, allow enough additional delay for the retransmission 

of lost packets. The default setting is Off.

Encoder Throttle

 - This option will allow the system to reduce the bitrate of encoded media when network conditions 

deteriorate. Disabling this option will prevent the system from lowering the quality of the encoded media but will 
also significantly reduce the ability of the system to handle networks with variable performance. This setting is set to 
Yes by default.

Hotswap CC Indicator

 - When enabled, this setting will activate a selected contact closure when a CrossLock backup 

interface is configured and has become activated due to failure of the primary interface(s). This is set to Disabled by 
default.

Hotswap CC Unit

 - This setting allows users to select which unit to indicate HotSwap failover on. This is set to Remote 

by default and additionally includes a Local and Both selection.

SYSTEM CLOCK

NTP Enabled

 - Enables the use of NTP network time synchronization. This setting is set to Yes by default.

NTP Server

 - This allows users to set the address of the NTP server. This is set for 0.comrex.pool.ntp.org by default.

Timezone

 - Users can set their Timezone in this setting. This allows for inputting a User’s Timezone by Region, Country, 

and Timezone.

ALTERNATE MODES

BRIC Normal Settings

•  Accept Incoming Connections

 - This determines if this BRIC-Link is used for incoming normal IP 

connections. If this function is not enabled, BRIC-Link will only support 

outgoing

 calls using BRIC Normal 

Mode.

EBU3266/SIP Settings

•  Accept Incoming Connections

 - This determines whether incoming calls are accepted in EBU3326/SIP 

format (used for compatibility with other manufacturers who follow this protocol).

Содержание BRIC-Link
































































































Отзывы:

Нет отзывов