Comrex BRIC-Link Скачать руководство пользователя страница 38

Страница: 38 / 95

CROSSLOCK VPN

UDP Port

- Sets the UDP port used for Crosslock VPN Connections. Default is set to UDP 9001.

Permissive -

Allows users to accept Crosslock connections from any unit. This is set to No by default.

Authentication -

Enables the authentication of connections. Default setting is No.

Protection

- Enables AES encryption and payload integrity protection to prevent tampering with or interception of

the transmitted content. This option has a SIGNIFICANT system overhead. Default setting is No.

Maximum Delay -

Maximum allowed target delay, in milliseconds. Set to 5000 ms by default.

FEC -

Enables data loss protection. This option controls protection on data transmitted to the remote end. Disabled

by default.

FEC Delay -

Amount of delay to allow for FEC. Lower packet rates will require higher delay to remain effective.

Rentransmit -

Enables retransmission of lost data. This option controls protection on data transmitted to the remote

end.

Header Compression -

Enables the compression of headers to reduce overhead, especially at lower bitrates. Default

is set to Yes.

Base FEC

- Applies a constant base amount of FEC sufficient to recover the specified rate of packet loss. Default is set

to 0%.

STUN Server -

Displays IP address of the STUN Server. Default is stun.comrex.com.

Always Connect -

Allows users to attempt to maintain a VPN connection to a selected peer whenever possible.

Default is set to None.

BRIC NORMAL SETTINGS

IP Port

- This option defines the incoming UDP port—the number to be used for incoming IP connections. The

default is

UDP 9000

. Crosslock connection is defaulted to

UDP 9001

. Note that since most BRIC-Link codecs attempt

a connection on this port number, changing it can mean the remote units in the field must dial specifically to the
new port number in order to connect to the BRIC-Link. An outgoing call must be made to a specific port number
in the form of

IP-ADDRESS:PORT#

. For example, dialing port

UDP 5004

on the Comrex test line is formatted

70.22.155.131:5004

Содержание BRIC-Link
































































































Результаты поиска

Содержание BRIC-Link

Отзывы:

Comrex BRIC-Link, Руководство по эксплуатации продукта, Страница: 38 / 95

Результаты поиска

Содержание BRIC-Link

Отзывы: