Computherm KonvekPRO Скачать руководство пользователя страница 26

Страница: 26 / 28

- 26 -

FREQUENTLY ASKED

QUESTIONS

When you think that your appliance is operating incorrectly or

encounter any problem while the appliance is being used then

we recommend that you read Frequently Asked Questions (FAQ)

available on our website, where we collected the problems and

questions that most frequently occur while our appliances are be-

ing used, along with the solutions thereto:

http://www.quantrax.hu/gyik/

The vast majority of the problems encountered can be solved

easily by using the hints available on our website, without

seeking professional help. If you have not found a solution to you

problem, please pay a visit to our qualified service.

Warning! The manufacturer does not assume responsibility

for any direct or indirect damages and loss of income

occurring while the appliance is being used.

Содержание KonvekPRO





























Результаты поиска

Содержание KonvekPRO

Отзывы:

Похожие инструкции для KonvekPRO

Бренды по названию

Популярные бренды

Computherm KonvekPRO, Руководство по эксплуатации

Результаты поиска

Содержание KonvekPRO

Отзывы:

Похожие инструкции для KonvekPRO

Бренды по названию

Популярные бренды