CompuSTAR Firstech CM800-S Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 21

CompuSTAR Firstech CM800-S Скачать руководство пользователя страница 3

3

Introduction

Thank you for purchasing a Firstech remote start system for your vehicle. The following installation
manual is intended for experienced and authorized remote start technicians. This is not a tutorial on how
to install. We highly recommend that you contact your local Firstech dealer and seek professional
installation.

Call 888-820-3690 or visit our website at

www.compustar.com

to locate your nearest dealer.

Caution: The Manufacture

r’s warranty will be void if this product is installed by anyone other than an

authorized dealer. Firstech reserves installation support services to authorized dealers only.

Kit(s) Contents

The CS8 Series Kits include all your basic components for basic install.

-

2 x Remotes

-

Starter Only Control Module CM800-S

-

1 x Antenna

- 1 x Hood Pin
- Pack of Wiring Harnesses

«
1
2
3
4
5
...
»

Содержание Firstech CM800-S






















Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды