Compaq TruCluster Server AA-RHGWB-TE Скачать руководство пользователя страница 225 | Manualshive

Страница: 225 / 320

background image

–

The bottom shelf tape drive (SCSI ID 3) is on SCSI Port A and is
also terminated on the drive with a 68-pin Micro-D terminator, part
number 0415619.

Figure 8–14: TL893 Three-Bus Configuration

MUC

SCSI Address 2

SCSI Port A

SCSI Port B

SCSI Port C

TZ89 Tape Drive
SCSI Address 5
(top shelf)

TZ89 Tape Drive
SCSI Address 4
(middle shelf)

TZ89 Tape Drive
SCSI Address 3
(bottom shelf)

0425031 (SCSI Diff Feed Through)

Drive Housing

0415619
(68-pin Micro-D Terminator)

0415619
(68-pin Micro-D Terminator)

ZK-1326U-AI

(Rear Connector Panel)

0415498 (50-Pin Micro-D Terminator)

;

0425017 (Cable)

620

409

9-0

1

620

409

9-0

1

620

409

9-0

1

•

The SCSI input for the TL896 is also high-density, 68-pin differential.
The default internal cabling configuration for the TL896 is a six-bus
configuration shown in Figure 8–15 as follows:

–

The upper bay top shelf tape drive (tape drive 5, SCSI ID 5) and
MUC (SCSI ID 2) are on SCSI Port D. To allow the use of the same
MUC and terminator used with the TL822 and TL826, a 68-pin to
50-pin adapter is used on the MUC to connect the SCSI cable from
the tape drive to the MUC. In Figure 8–15 it is shown as part number
0425031, SCSI Diff Feed Through. This SCSI bus is terminated on
the MUC with terminator part number 0415498, a 50-pin Micro-D
terminator.

–

The upper bay middle shelf tape drive (tape drive 4, SCSI ID 4) is on
SCSI Port E and is terminated on the tape drive.

–

The upper bay bottom shelf tape drive (tape drive 3, SCSI ID 3) is on
SCSI Port F and is terminated on the tape drive.

Configuring a Shared SCSI Bus for Tape Drive Use 8–45

«
...
223
224
225
226
227
...
»

Содержание TruCluster Server AA-RHGWB-TE

































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TruCluster Server AA-RHGWB-TE

Бренд: IBM Страницы: 56

System x3350 Type 4192

Бренд: IBM Страницы: 84

Бренд: IBM Страницы: 16

Бренд: IBM Страницы: 96

Бренд: IBM Страницы: 75

eServer xSeries 335 Type 8676

Бренд: IBM Страницы: 178

DPR-1260 - RangeBooster G Multifunction Print Server

Бренд: D-Link Страницы: 55

Бренд: D-Link Страницы: 49

Бренд: Artesyn Embedded Technology Страницы: 2

Бренд: CasaTunes Страницы: 7

Бренд: MATE Страницы: 68

Бренд: ZLAN Страницы: 16

Бренд: ZLAN Страницы: 17

Бренд: AMX Страницы: 2

Бренд: Altigen Страницы: 462

Бренд: SNAP Страницы: 2

Бренд: Gigabyte Страницы: 158

Бренд: Oracle Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды