Compaq TruCluster Server AA-RHGWB-TE Скачать руководство пользователя страница 252 | Manualshive

Страница: 252 / 320

background image

9.1 Using SCSI Bus Signal Converters

A SCSI bus signal converter allows you to couple a differential bus segment
to a single-ended bus segment, allowing the mixing of differential and
single-ended devices on the same SCSI bus to isolate bus segments for
maintenance purposes.

Each SCSI signal converter has a single-ended side and a differential side as
follows:

•

DWZZA — 8-bit data path

•

DWZZB — 16-bit data path

•

DS-BA35X-DA 16-bit personality module

______________________

Note

_______________________

Some UltraSCSI documentation uses the UltraSCSI "bus
expander" term when referring to the DWZZB and UltraSCSI
signal converters. Other UltraSCSI documentation refers to some
UltraSCSI products as bus extender/converters.

For TruCluster Server there are no supported standalone
UltraSCSI bus expanders (DWZZC).

In this manual, any device that converts a differential signal to
a single-ended signal is referred to as a signal converter (the
DS-BA35X-DA personality module contains a DWZZA-on-a-chip
or DOC chip).

A SCSI signal converter is required when you want to connect devices with
different transmission modes.

9.1.1 Types of SCSI Bus Signal Converters

Signal converters can be standalone units or StorageWorks building blocks
(SBBs) that are installed in a storage shelf disk slot. You must use the signal
converter module that is appropriate for your hardware configuration.

For example, use a DWZZA-VA signal converter to connect a wide,
differential host bus adapter to a BA350 (single-ended and narrow) storage
shelf, but use a DWZZB-VW signal converter to connect a wide, differential
host bus adapter to a non-UltraSCSI BA356 (single-ended and wide) storage
shelf. The DS-BA35X-DA personality module is used in an UltraSCSI BA356
to connect an UltraSCSI host bus adapter to the single-ended disks in the
UltraSCSI BA356. You could install a DWZZB-VW in an UltraSCSI BA356,

9–2 Configurations Using External Termination or Radial Connections to Non-UltraSCSI Devices

«
...
250
251
252
253
254
...
»

Содержание TruCluster Server AA-RHGWB-TE

































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TruCluster Server AA-RHGWB-TE

Бренд: D-Link Страницы: 38

Epress EtherNetwork DP-301P+

Бренд: D-Link Страницы: 2

Бренд: Basalte Страницы: 2

Бренд: Xantech Страницы: 52

iDataPlex dx320 6385

Бренд: IBM Страницы: 60

AMX Vision2 V2-MASTER-1210

Бренд: Harman Страницы: 2

Бренд: B&B Страницы: 70

Silex Pricom SX-2000U2

Бренд: Silex technology Страницы: 1

Бренд: Sollae Systems Страницы: 27

Ultra Enterprise 3000

Бренд: Sun Microsystems Страницы: 48

PLATINUM 1500 IR M5

Бренд: MAXDATA Страницы: 44

UCS Invicta C3124SA

Бренд: Cisco Страницы: 60

Бренд: Cisco Страницы: 54

UCS Invicta C3124SA

Бренд: Cisco Страницы: 40

Бренд: Cisco Страницы: 132

Бренд: Cisco Страницы: 46

Бренд: Cisco Страницы: 35

Бренд: Cisco Страницы: 188

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды