comoc C130 D 2015, Руководство по эксплуатации и обслуживанию

Страница: 38 / 48

N.B.
: the equipment to be used for this operation is not supplied with the machine.
14. Remove the front rubber-pressing blade (9) ( Fig.9 ).
15. Remove the front rubber blade (10) and replace it ( Fig.10 ).
16. To fix the front rubber-pressing blade to the squeegee body, follow the instructions in reverse order.
17. Use the appropriate tool to rotate the retainer blades (11) that fix the rear rubber-pressing blade (12)
to the squeegee body ( Fig.11 ).
N.B. : the equipment to be used for this operation is not supplied with the machine.
18. Remove the rear rubber-pressing blade (13) ( Fig.12 ).
19. Remove the rear rubber blade (14) and replace it ( Fig.17 ).
20. To fix the rear rubber-pressing blade to the squeegee body, follow the instructions in reverse order.
21. Repeat the operations in reverse order to reassemble all the parts.
ATTENTION : before using the machine, remember to adjust the squeegee body. Read
“ ADJUSTING THE SQUEEGEE BODY RUBBER BLADES ”.
ATTENTION : it is good practice to replace both squeegee blades, to ensure good results when
drying the floor.
REPLACING THE SQUEEGEE SPLASH GUARD BARS RUBBER
Ensuring the good condition of the squeegee body's splash guard bar guarantees better floor cleaning
and drying results, as well as a longer service life for the vacuum motor.
To replace the squeegee body's splash guard bar rubber do as follows:
1. Select the i-drive program “transport” by rotating the knob to position “A” as shown in ( Fig.1 ).
N.B. : by rotating the i-drive selector to the transfer program, all the brush heads and the squeegee
body will move to their idle positions (raised off floor).
N.B. : on the screen of the command display, the machine silhouette will have a green icon only
the symbol that identifies the traction motor .
2. Take the machine to the maintenance area.
NOTE
: the place designated for this operation must comply with current environmental protection
regulations.
3. As soon as the machine has reached the maintenance area, make sure it is in a safe condition
(read “ MACHINE SAFETY ”).
CAUTION : these operations must be carried out using protective gloves to avoid any possible
contact with the edges or tips of metal objects.
4. Stand on the right side of the machine.
5. Remove the retainer (1) from the pin (2) in the squeegee body ( Fig.2 ).
6. Free the pin (2) in the squeegee body from the slot (3) in the squeegee control bar (4) ( Fig.3 ).
7. Turn the right splash guard bar (4) as far as it will go.
8. Use the appropriate tool to remove the screws (5) that fix the rubber-pressing blade (6) to the splash
guard bar ( Fig.5 ).
N.B. : the equipment to be used for this operation is not supplied with the machine.
9. Remove the rubber-pressing blade (6) (
Fig.6
).
REPLACING THE SCRUBBING BRUSH HEAD SPLASH GUARD RUBBER
The good condition of the splash guard rubber of the scrubbing brush head guarantees better cleaning
of the floor.
To replace the splash guard rubber of the scrubbing brush head, proceed as follows:
1. Select the i-drive program “transport” by rotating the knob to position “A” as shown in (
Fig.1
).
N.B. : by rotating the i-drive selector to the transfer program, all the brush heads and the squeegee
body will move to their idle positions (raised off floor).
N.B. : on the screen of the command display, the machine silhouette will have a green icon only
the symbol that identifies the traction motor .
2. Take the machine to the maintenance area.
NOTE : the place designated for this operation must comply with current environmental protection
regulations.
3. As soon as the machine has reached the maintenance area, make sure it is in a safe condition
(read “ MACHINE SAFETY ”).
CAUTION : these operations must be carried out using protective gloves to avoid any possible
contact with the edges or tips of metal objects.
4. Stand on the right side of the machine.
5. Using a suitable tool remove the screws (1) fixing the scrubbing brush head splash guard support
(2) ( Fig.2 ).
N.B.
: the equipment to be used for this operation is not supplied with the machine.
6. Remove the scrubbing brush head splash guard support from the machine.
7. Use the appropriate tool to remove the screws (3) that fix the rubber-pressing blade (4) to the
scrubbing brush head splash guard support ( Fig.3 ).
N.B. : the equipment to be used for this operation is not supplied with the machine.
8. Remove the rubber-pressing blade (4) ( Fig.4 ).
9. Remove the splash guard rubber (5) and replace it ( Fig.5 ).
10. Repeat the operations in reverse order to reassemble all the parts.
11. Repeat steps 4 - 11 on the left-hand side of the machine.
ATTENTION : before using the machine remember to adjust the squeegee body slash guard bar
rubber, read the section “ ADJUSTING THE BRUSH HEAD SPLASH GUARD RUBBER ”.
10. Remove the splash guard rubber (7) and replace it ( Fig.7 ).
11. Repeat the operations in reverse order to reassemble all the parts.
12. Repeat steps 5 - 11 also for the left-hand side of the machine.
ATTENTION : before using the machine remember to adjust the squeegee body slash guard bar
rubber, read the section “ ADJUSTING THE SQUEEGEE BODY SPLASH GUARD BAR
RUBBER ”.
38
7 8
7 8
9
9
9
10 11 12
10 11 12
12
17
13
1
A
3 2
2 2
1 3
4
2 3 1
A
1
2
4
3
5 4
4 5
6 5 4
6
5
6
6 7