7.
Open the detergent solution flow into the machine's water system by turning the tap control lever (5)
in the direction indicated by the arrow (
Fig.7
).
8.
Select the speed level (for example “step-01”), and turn the knob (6) on the direction selection
lever (7) (
Fig.8
), under the steering wheel.
N.B.
: adjust the forward speed to suit the adhesion conditions.
9.
Select the direction in which you want to move the machine. For example, if you want to move
forward, shift the direction selector lever (7) in the direction shown by the arrow (
Fig.9
).
N.B.
: To select the forward gear (F) you need to first shift the lever up and then shift it in the
direction indicated by the arrow (
Fig.9
).
N.B.
: the letter “F” will appear on the command display indicating that the forward gear is
engaged.
N.B.
: on the command display, near the letter “F” the number “1” is displayed indicating that
the forward speed engaged is “step-01”.
10.
Release the parking brake by moving the parking brake lever (8) next to the operator's seat in the
direction indicated by the arrow (
Fig.10
).
N.B.
: the symbol regarding the parking brake being engaged will appear on the command
display.
11.
Press the drive pedal (9) to begin moving the machine (
Fig.11
).
If the working program selected is “SCRUBBING WITH DRYING”, the squeegee and brush head will
lower until they touch the floor. As soon as the drive pedal is pressed, the traction motor, brush head
motor and vacuum motor will start working. As a result, the solenoid valve will also be activated and
detergent solution will be dispensed onto the brushes.
During the first few metres, check that there is sufficient solution and that the squeegee is drying
correctly.
At this point the machine will begin operating at maximum efficiency until either the detergent solution
or both fuels have run out.
Before cleaning, pick up large pieces of waste. Pick up wire, tape, string, large pieces of wood or
other refuse that could wrap around the brushes or get entangled
Drive the machine in a straight line. Avoid hitting obstacles and scratching the sides of the machine.
Overlap the cleaning track by a few centimetres.
Avoid turning the steering wheel abruptly when the machine is moving. The machine responds
rapidly to the movements of the steering wheel. Avoid hairpin turns, except in emergencies.
Adjust the speed of the machine, the pressure of the brushes and the flow of the solution according
to the type of cleaning to be carried out.
Drive the machine slowly on inclines. Use the brake pedal to control the speed when going down an
incline. Where there is a slop, carry out the scrubbing by moving the machine upwards rather than
downwards.
ATTENTION
: when you use the machine, slow down on ramps and slippery surfaces.
Do not use the machine in areas where the ambient temperature is higher than 43 ° C (110° F). Do
not use the scrubbing functions in areas where the ambient temperature is less than freezing 0 °C
(32 °F).
ATTENTION
: when using the machine, do not clean on slopes greater than 8.7% or when
transporting on slopes greater than 12%.
WORKING PROGRAM: TRANSFER
Selecting the program “TRANSFER”, the control display screen will appear as shown in the figure.
All the brush heads and the squeegee are raised from the floor and do not operate.
Le The icons visible in the transfer program are:
1. Machine silhouette, where only the icon regarding the traction motor is green.
N.B.
: the grey symbols identify the components that are not active. the green symbols identify the
components that are active. the red symbols identify the components that are faulty.
2. Indicator light indicating the side lights are active (green).
3. Indicator light indicating the low beam lights are active (green).
4. Indicator light indicating the general alarm (red).
5. Indicator light indicating the braking system oil is low (red).
6. Indicator light indicating the parking brake is engaged (red).
12. Machine's draw level bar.
14. Check button, allows you to display the screen regarding the working condition of the machine.
N.B.
: To understand which parameters are displayed on the screen, read the section “
15. Hour meter.
N.B.
: the value displayed represents
the total time the machine has been used.
19. Abbreviation identifying the machine's direction parameters (gear and speed).
N.B.
: the letter that precedes the number identifies the direction selected, to adjust the direction
”.
N.B.
: the number that follows the letter identifies the speed selected, to adjust the speed read the
”.
20. Setting button, allows you to make temporary changes to the machine parameters.
22. Battery charge level bar.
N.B.
: To understand the function of the battery charge level bar, read the section “
”.
23. Activating– deactivating dipped headlights button.
N.B.
: setting the main switch to “I” the sidelights will come on. To switch on the low beam
headlights press the button (6) on the instrument panel.
N.B.
: The low beam headlights are active when the symbol (10) on the instrument panel is green.
To use the transfer program, proceed as follows:
1. Sit on the driver’s seat.
2. Turn on the machine (
Fig.1
).
3.
The first screen shown displays the manufacturer's logo and the name of the machine.
4. The second screen shown displays the working screen.
5.
Select the “transfer” program with the knob of the I-Drive device (26) (
Fig.2
).
6.
Select the speed level (for example “step-01”), turn the knob (27) on the direction selection lever
(28) (
Fig.3
), under the steering wheel.
N.B.
: adjust the forward speed to suit the adhesion conditions.
20
7
5
8
9
6
7
7
10
8
11
9
1
2
19
3
4
5
6
15
23
12
22
14
20
2
1
24
26
25
3
27
28
