N.B.
: to select the forward gear (F) you need to first shift the lever up and then shift it in the
direction indicated by the arrow (
Fig.4
).
N.B.
: the letter “F” will appear on the command display indicating that the forward gear is
engaged (19).
N.B.
: on the command display, near the letter “F” the number “1” is displayed indicating that
the forward speed engaged is “step-01” (19).
8.
Release the parking brake by moving the parking brake lever (29), beside of the operator's seat,
in the direction shown by the arrow (
Fig.5
).
N.B.
: the symbol regarding the parking brake being engaged will appear on the command
display (6).
9.
Select the type of program you want to use, the pre-set program is “STANDARD” (17).
N.B.
: the grey symbols identify the components that are not active. the green symbols identify the
components that are active.
N.B.
: to view or change the parameters of the “ECO” or “STD” or “PLUS” programs read the
section “CHANGING WORKING PROGRAM PARAMETERS” in the chapter “WORK”.
10.
pressing the drive pedal (30) (
Fig.6
), the machine starts to move, both the brush heads and the
squeegee go to the work position, once they are in contact with the floor all the electric motors
start operating.
If, when working, you need to temporarily change the parameters of the pressure on the brushes or
the amount of detergent solution dispensed, read the sections “
” or “
TEMPORARY ADJUSTMENT OF DETERGENT SOLUTION DISPENSING
”
in the chapter “WORK”.
If, when working, it is necessary to use the dipped-beam headlights, press the button (9) on the
command display.
N.B.
: setting the main switch to “I” the sidelights will come on, and on the instrument panel the
relative symbol will come on (2)
N.B.
: To access the dipped-beam headlights, press the button (23) on the instrument panel.
N.B.
: The low beam headlights are active when the symbol (23) on the instrument panel is green,
the relative symbol (3) on the command display comes on.
If, when working, the machine stops and the drive pedal is released, the brush motors and the solenoid
valve will switch off, and after a few second the brush heads will raise up off the ground and return to
the rest position.
N.B.:
by pressing the forward movement pedal it will start working with the same program and with
the same parameters that were set before it stopped.
N.B.:
if reverse is carried out with this program active, the brush head body will remain in contact
with the floor, the motor will continue working but the solenoid valve will no longer dispense
any detergent solution onto the brushes.
If, when working, the solution tank float indicator light (9) comes on, stop the machine and fill the solution
tank.
N.B.
: to fill the solution tank with detergent solution, refer to “
the “MACHINE PREPARATION” chapter.
If, when working, the general alarm indicator light (4) comes on, stop the machine and contact the
nearest service centre.
If, when working, the braking system low oil level indicator light (5) comes on, stop the machine and
contact the nearest service centre.
If, when working, the low detergent level indicator light (10) comes on, stop the machine and top up the
detergent inside the canister.
ATTENTION: never switch off the machine while the
squeegee and/or brush head is in contact with the floor
HOUR METER
GENERATOR CHARGE LEVEL SIGNALLING DEVICE
There is a box (1) in the work screen of the command display that allows you to see the total time
the machine has been used. The numbers before the letter “h” identify the hours, while the numbers
before the letter “m” identify the tenths of an hour (a tenth of an hour corresponds to six minutes).
The flashing “:” symbol indicates that the hour meter is counting the machine functioning time.
The graphical symbol (2), which indicates the generator's charge level, is present on the command
display's work screen.
N.B.
: Always keep the speed at maximum in order to ensure the generator's proper functionality.
SELECTING THE OPERATING DIRECTION
The machine has a lever for selecting the travel direction (1) under the steering wheel (
Fig.1
).
N.B.
: You can choose between forwards (F) and reverse (R). Putting the lever in the middle
however you get neutral (N).
N.B.
: to select the forward gear (F) you need to first shift the lever up and then shift it in the
direction indicated by the arrow (
Fig.1
).
N.B.
: to go from forward (F) to neutral (N) first move the lever in the direction indicated by the
arrow (
Fig.2
).
ATTENTION
: to select reverse (R) you need to first shift the lever up and then shift it in the
direction indicated by the arrow (
Fig.3
). With reverse gear engaged if you press the
drive pedal a buzzer will sound and the white rear lights come on.
N.B.
: as soon as a gear is selected, the identification letter appears on the command display
(2).
24
2
1
24
26
25
3
27
28
4
28
6
5
29
30
2
1
2
4
1
2
3
1
1
1
