Comms365 C365-5G-Mini Скачать руководство пользователя страница 45

Страница: 45 / 58

C365-5G-Mini User Manual CB-V1.1

www.comms365.com | 01234 865880 | [email protected]

•

Status:

Show the Wi-Fi signal strength, mode, SSID and so on.

•

Operating frequency Mode:

supports 802.11b/g/n. the Legacy means 802.11b/g. “N” means

802.11n.

•

Channel:

Channel 1-11 supported.

•

Width:

20MHz and 40MHz.

•

Transmit Power:

From 0dBm to 20dBm supported.

3.6.6.2 Wi-Fi Advanced Configuration

•

Country Code:

Use ISO/IEC 3166 alpha2 country codes.

•

Distance Optimization:

Distance to farthest network member in meters.

•

Fragmentation Threshold

•

RTS/CTS Threshold

3.6.6.3 Wi-Fi Interface Configuration

•

ESSID:

Extended Service Set Identifier. It is the broadcast name.

•

Mode:

Supported options.

Содержание C365-5G-Mini



























































Результаты поиска

Содержание C365-5G-Mini

Отзывы:

Похожие инструкции для C365-5G-Mini

Бренды по названию

Популярные бренды

Comms365 C365-5G-Mini, Руководство пользователя

Результаты поиска

Содержание C365-5G-Mini

Отзывы:

Похожие инструкции для C365-5G-Mini

Бренды по названию

Популярные бренды