ComAp InteliNano NT Plus Скачать руководство пользователя страница 1

Страница: 1 / 90

ComAp, a.s.

Kundratka 17, 180 00 Praha 8, Czech Republic
Tel: +420 246 012 111, Fax: +420 266 316 647

Reference Guide

ABLE OF CONTENTS

Document information ...................................................................................................................... 3

Clarification of notation ........................................................................................................... 3

1.1

Conformity Declaration ........................................................................................................... 3

1.2

Important ................................................................................................................................ 3

1.3

Text ........................................................................................................................................ 5

1.4

System Overview ............................................................................................................................. 6

General description ................................................................................................................ 6

2.1

Configurability ........................................................................................................................ 6

2.2

Application Overview ........................................................................................................................ 7

AMF

– Automatic Mains Failure start ..................................................................................... 7

3.1

MRS

– Manual Remote Start ................................................................................................. 8

3.2

True RMS measurement ........................................................................................................ 9

3.3

Installation and wiring ..................................................................................................................... 10

Mounting............................................................................................................................... 10

4.1

Package contents ................................................................................................................. 11

4.2

Terminal diagram ................................................................................................................. 12

4.3

Power supply ........................................................................................................................ 13

4.4

D+ ......................................................................................................................................... 14

4.5

Voltage measurement and generator connection types ...................................................... 15

4.6

Current measurement .......................................................................................................... 22

4.7

Binary inputs ........................................................................................................................ 23

4.8

Binary outputs ...................................................................................................................... 24

4.9

Analog inputs ....................................................................................................................... 25

4.10

AMF application wiring diagram ........................................................................................... 27

5.1

MRS application wiring diagram .......................................................................................... 28

5.2

Controller Settings .......................................................................................................................... 29

Setup mode .......................................................................................................................... 29

6.1

Inputs and Outputs ......................................................................................................................... 33

Normally Open Contact ........................................................................................................ 34

7.1

InteliNano

InteliNano NT



Plus

Modular Gen-set Controller with Current
Measurement

Compact Controller for Stand-by Operating Gen-sets

SW version 2.0.1.x, July 2015

Содержание InteliNano NT Plus



























































































Результаты поиска

Содержание InteliNano NT Plus

Отзывы:

Бренды по названию

Популярные бренды

ComAp InteliNano NT Plus, Справочное руководство

Результаты поиска

Содержание InteliNano NT Plus

Отзывы:

Бренды по названию

Популярные бренды