ComAp ID-FLX-Lite-PC Скачать руководство пользователя

Страница: 73 / 211

InteliDrive Lite - 1.2.1 Global guide

Note:

If the connected engine is Cummins communicating via RS232, it is necessary to set the setpoint Basic

settings: COM1 mode (or COM2 mode if IL-NT-RS232-485) = ECULINK.

Loss of communication causes shutdown of the running engine. On the contrary, the ECU can be switched off

at quiescent engine that means not-communicating ECU is in that moment normal situation. All values from

ECU shall show ####, but no alarm is displayed. The output ECU CommOK follows the real situation that

means it is not active anytime when the ECU does not communicate.

The output ECU PwrRelay closes at the beginning of prestart and opens if the engine shall be stopped.

The engine is started via standard contact output or via CAN bus.

Practical examples of values read from ECU:

Value name

Short name

Dimension

Type

Frame

name

EngOil Filter Diff.Press

OilDiffPres

bar

ANA

Amber Warning Lamp

AmberWrnLamp

BIN

DM1

Malfunction Lamp

MalfunctLamp

BIN

DM1

Protect Lamp

ProtectLamp

BIN

DM1

Red Stop Lamp

RedStopLamp

BIN

DM1

Engine speed

RPM

ANA

EEC1

Engine Oil Pressure

EngOil Press

bar

ANA

EFLP1

Coolant Temp

°C

ANA

ET1

Содержание ID-FLX-Lite-PC




















































































































































































































Результаты поиска

Содержание ID-FLX-Lite-PC

Отзывы:

Похожие инструкции для ID-FLX-Lite-PC

Бренды по названию

Популярные бренды

ComAp ID-FLX-Lite-PC, Глобальное руководство

Результаты поиска

Содержание ID-FLX-Lite-PC

Отзывы:

Похожие инструкции для ID-FLX-Lite-PC

Бренды по названию

Популярные бренды