ComAp ID-FLX-Lite-PC Скачать руководство пользователя

Страница: 67 / 211

InteliDrive Lite - 1.2.1 Global guide

Timer2

Output activates when Timer2 is active. Simultaneously the engine is started when is in AUT mode.

Glow plugs

The output closes prior to the engine start (Prestart) and opens when Starting RPM speed is reached. During

repeated crank attempts the output is opened.

LBO Glow Plugs is closed prior to every attempt to start the engine for time set in setpoint Preglow.

Conveyor

Binary output function of Conveyor. See Binary input Conveyor.

SpeedSwitch

Binary output from Speed switch comparator – see Regulator setpoint group.

LoadSwitch

Binary output from Load switch comparator – see Load limit setpoint group.

Close Load

Output is controlled by panel 0/1 button when Basic settings: Panel Button = Close Load, engine is running and

no Sd/Cd alarm is active. Close Load output is not closed in Idle and Cooling states and is disconnected when

any Sd/Cd alarm is activated.

Toggle

Output is controlled by panel 0/1 button when Basic settings: Panel Button = Toggle. This setting changes the

Toggle output without any relation to Engine state or Alarm activity even if in OFF mode.

RemoteControl 1, 2, 3, 4, 5, 6, 7, 8

Allows configure Remote control switches to physical binary outputs. These switches are accessible from PC

tools LiteEdit (see picture below) or InteliMonitor by button

and it can be controlled via ModBus

communication.

SpdUpButtEcho

Output copies level of button Speed Up which is useful for manual speed settings of mechanical engines

directly from controller.

Содержание ID-FLX-Lite-PC




















































































































































































































Результаты поиска

Содержание ID-FLX-Lite-PC

Отзывы:

Похожие инструкции для ID-FLX-Lite-PC

Бренды по названию

Популярные бренды

ComAp ID-FLX-Lite-PC, Глобальное руководство

Результаты поиска

Содержание ID-FLX-Lite-PC

Отзывы:

Похожие инструкции для ID-FLX-Lite-PC

Бренды по названию

Популярные бренды