ComAp ID-FLX-Lite-PC Скачать руководство пользователя

Страница: 124 / 211

InteliDrive Lite - 1.2.1 Global guide

124

Setpoint group

Comms settings

Related FW

1.2.1

Range [units]

[-]

Default value

192.168.1.1

Force value

Step

[-]

Comm object

24373

Related applications

Config level

Standard

Setpoint visibility

Always

Description

IP address of gateway for IB-Lite

IBLite GateIP

back to List of setpoints

Setpoint group

Comms settings

Related FW

1.2.1

Range [units]

[-]

Default value

ENABLED

Force value

Step

[-]

Comm object

24259

Related applications

Config level

Standard

Setpoint visibility

Always

Description

Dynamic Host Configuration Protocol for IP address setting can be used or blocked.

DISABLED: Block the function of DHCP, this option is worth, if you wanna adjust stable IP address e.g. for

WebServer connection or InteliMonitor PC tool.

Note:

Can occured collision of IP addresses in local network with devices as printer, router etc.!

ENABLED: Dynamically change IP address of the controller after each switch on of the controller. IP

address collision protection. Default state.

IBLite DHCP

back to List of setpoints

Setpoint group

Comms settings

Related FW

1.2.1

Range [units]

[-]

Default value

Force value

Step

[-]

Comm object

24374

Related applications

Config level

Standard

Setpoint visibility

Always

Description

This sepoint is for adjustment of port for ComAp communication over IB-Lite or IL-NT-GPRS module.

Standard ComAp port is 23, what is default value of this setpoint.

ComAp Port

back to List of setpoints

Содержание ID-FLX-Lite-PC




















































































































































































































Результаты поиска

Содержание ID-FLX-Lite-PC

Отзывы:

Похожие инструкции для ID-FLX-Lite-PC

Бренды по названию

Популярные бренды

ComAp ID-FLX-Lite-PC, Глобальное руководство

Результаты поиска

Содержание ID-FLX-Lite-PC

Отзывы:

Похожие инструкции для ID-FLX-Lite-PC

Бренды по названию

Популярные бренды