COMAC ANTEA 50 B, Руководство по эксплуатации и обслуживанию

Страница: 33 / 44

N.B.
: the place designated for this operation must comply with current environmental protection
regulations.
13. Repeat the operations described above for the front brush as well.
N.B. : If the height of the bristles is less than 10mm, replace the brush. To insert the brush inside
the brush head body, read the paragraph “ INSTALLING THE BRUSH (65BTS double brush
versions) ”.
14. Repeat the operations in reverse order to reassemble all the parts.
CLEANING THE DEBRIS HOPPER (50BTS double brush versions)
The thorough cleaning of the debris hopper ensures better floor cleaning performance. To clean the
debris hopper, proceed as follows:
1. Take the device to the dedicated maintenance area.
N.B.
: the place designated for this operation must comply with current environmental protection
regulations.
2. Take all necessary steps to ensure that the device is in a safe condition (see “ MACHINE SAFETY ”).
N.B. : these operations must be carried out using protective gloves to avoid any possible contact
with the edges or tips of metal objects.
3. Position yourself on the right-hand side of the appliance.
4. Loosen the retainer knob (1) ( Fig. 1 ).
5. Remove the right side splash guard support (2), making sure to shift the blade before removing the
splash guard support itself ( Fig. 2 ).
6. Extract the debris hopper (3) from the brush head unit ( Fig. 3 ).
7. Clean the inside of the debris hopper with a stream of running water, using a brush to remove any
dirt residues if necessary.
8. Repeat the operations in reverse order to reassemble all the parts.
3
3
1 2
1 2
CLEANING THE DEBRIS HOPPER (65BTS double brush versions)
The thorough cleaning of the debris hopper ensures better floor cleaning performance. To clean the
debris hopper, proceed as follows:
1. Take the device to the dedicated maintenance area.
2. Take all necessary steps to ensure that the device is in a safe condition (see “ MACHINE SAFETY ”).
N.B.
: these operations must be carried out using protective gloves to avoid any possible contact
with the edges or tips of metal objects.
3. Stand on the left side of the appliance.
4. Remove the left side splash guard support (1) ( Fig. 1 ).
5. Extract the debris hopper (2) from the brush head body ( Fig. 2 ).
N.B. : To do this, use the moulded handle on the lower part of the debris hopper.
6. Clean the inside of the debris hopper with a stream of running water, using a brush to remove any
dirt residues if necessary.
N.B. : the place designated for this operation must comply with current environmental protection
regulations.
7. Repeat the operations in reverse order to reassemble all the parts.
To clean the debris hopper with the spray gun, for versions with the SST system, proceed as follows:
1. Take the device to the dedicated maintenance area.
2. Lift the brush head body and press the “BRUSH HEAD CONTROL” button (1) on the control panel
( Fig. 1 ).
3. Raise the squeegee unit and turn the squeegee control lever (2) in the direction of the arrow in
( Fig. 2 ). The lever is located on the back of the device.
CAUTION : these operations must be carried out using protective gloves to avoid any possible
contact with the edges or tips of metal objects.
4. Remove the left side splash guard support (3) ( Fig. 3 ).
1 2
1 2
3
3
1
1
2
2
5. Extract the debris hopper (4) from the brush head unit ( Fig. 4 ).
N.B. : To do this, use the moulded handle on the lower part of the debris hopper.
6. Remove the spray gun kit from the storage compartment ( Fig. 5 ).
7. Connect the male quick-coupler (5) on the spiral hose (6) to the female quick-coupler (7) on the front
of the appliance ( Fig. 6 ).
8. Connect the male quick-coupler (8) on the spray gun (9) to the female quick-coupler (10) on spiral
hose (6) ( Fig. 7 ).
9. Activate the spray gun kit by pressing the button (11) on the steering column ( Fig. 8 ).
CAUTION : when using the optional tank cleaning kit, you are advised to always wear goggles to
avoid any risk of serious injury to your eyes.
N.B. : Before activating the optional tank cleaning kit, check the level indicator (12) to see how
much solution there is in the solution tank ( Fig. 9 ).
10. Start the delivery of detergent jet by pressing the lever (13) on the spray gun ( Fig. 10 ).
N.B.
: To adjust the solution jet coming out of the spray gun
turn the knob (14) on the accessory
itself ( Fig. 11 ).
11. Clean the inside of the debris hopper under a jet of detergent solution, using a spatula to remove any
dirt residues if necessary.
N.B. : the place designated for this operation must comply with current environmental protection
regulations.
12. Repeat the operations in reverse order to reassemble all the parts.
5 4
4
6
6
5
7
7 8
12
9
10 11
8
9
13
14
10 11
CLEANING THE VACUUM TUBE
Careful cleaning of the vacuum hose guarantees better cleaning of the floor as well as a longer vacuum
motor life. Proceed as follows to clean the vacuum hose:
1. Take the device to the dedicated maintenance area.
2. Take all necessary steps to ensure that the device is in a safe condition (see “ MACHINE SAFETY ”).
CAUTION : users are advised to always wear protective gloves, to avoid the risk of serious injury
to hands.
3. Remove the vacuum hose (1) from the vacuum nozzle (2) on the squeegee unit ( Fig. 1 ).
4. Remove the vacuum hose (1) via the hole on the back of the recovery tank ( Fig. 2 ).
5. Remove the recovery tank drainage hose from the clamps.
6. Rinse the inside of the vacuum hose with a jet of running water.
7. Repeat the operations in reverse order to reassemble all the parts.
N.B. : Pay particular attention when placing the vacuum hose behind the lifting chain, as indicated
on the label ( Fig. 3 ).
To clean the vacuum hose with the spray gun, for versions with the SST system, proceed as follows:
1. Take the device to the dedicated maintenance area.
2. Lift the brush head body and press the “BRUSH HEAD CONTROL” button (1) on the control panel
( Fig. 1 ).
3. Raise the squeegee unit and turn the squeegee control lever (2) in the direction of the arrow in
( Fig. 2 ). The lever is located on the back of the device.
1
2
1
1 2 3
33