COMAC ANTEA 50 B, Руководство по эксплуатации и обслуживанию

Страница: 20 / 44

INSTALLING THE BRUSH (BT double brush versions)
For packaging reasons, the brush is supplied disassembled from the device. To assemble it on the brush
head unit, proceed as follows:
1. Take all necessary steps to ensure that the device is in a safe condition (see “ MACHINE SAFETY ”).
2. Position yourself at the rear of the appliance.
3. Lower the brush head unit by pressing the brush head control pedal (1) on the back of the appliance
(
Fig. 1
).
4. Position yourself at the front of the appliance.
5. If the splash guard carters (2) are present, remove them ( Fig. 2 ) and lay them gently on the ground.
6. Position yourself at the rear of the appliance.
7. Raise the brush head body off the floor and press the brush head control pedal (1) on the rear of
the device ( Fig. 3 ).
8. With the brush head UP, insert the brush in the plate housing underneath the brush head, turning it
until the three buttons engage with the niches on the plate itself.
9. Press the brush-holder plate latch (3) and simultaneously rotate the brush (4) according to the
direction indicated in the image (
Fig. 4
).
N.B. : The image Fig. 4 shows the rotation direction of the left brush.
10. When brush rotation is prevented, turn until the button on the brush is engaged in the coupling spring
on the brush-holder plate.
11. Reassemble the brush head splash guard carters.
1 1
3 1
2
2
4
1
1
INSTALLING THE BRUSH HEAD BRUSH (BT double brush versions)
For packaging reasons, the brush head splash guard is supplied disassembled from the device, and
must be assembled on the brush head unit as follows:
1. Take all necessary steps to ensure that the device is in a safe condition (see “ MACHINE SAFETY ”).
CAUTION : these operations must be carried out using protective gloves to avoid any possible
contact with the edges or tips of metal objects.
2. Position yourself at the front of the appliance.
3. Insert the pins (1) present on the left splash guard (2) ( Fig. 1 ) into the holes (3) present in the brush
head body (4) ( Fig. 2 ).
4. Repeat the same operation for the right splash guard also.
1 4
2 3
2 1
INSTALLING THE BRUSH (50BTS double brush versions)
To assemble the brushes to bush head unit, which for reasons of packaging are supplied disassembled
from the machine, proceed as follows:
1. Take all necessary steps to ensure that the device is in a safe condition (see “ MACHINE SAFETY ”).
CAUTION
: these operations must be carried out using protective gloves to avoid any possible
contact with the edges or tips of metal objects.
2. Position yourself on the right-hand side of the appliance.
3. Loosen the retainer knob (1) ( Fig. 1 ).
4. Remove the right side splash guard support (2), making sure to shift the blade before removing the
splash guard support itself ( Fig. 2 ).
5. Remove the rear brush guide hub (3) (
Fig. 3
).
6. Insert the rear brush into the tunnel, taking care to properly position the drive pins (4) on the guide
hub (5) in the slits present on the brush ( Fig. 4 ).
3
3
1 2
1 2
7. Insert the hub (3) into the brush, taking care to properly position the drive pins (6) in the slits on the
brush ( Fig. 5 ).
8. Repeat the operations described above for the front brush as well.
N.B. : The rear brush (work direction) should always be the light blue one.
N.B. : The brush bristles are properly positioned if they form an X when viewed from above. Both
vertices, of the shortest height, should converge towards the centre.
9. Repeat the operations in reverse order to reassemble all the parts.
4
5
6
3
5 4
INSTALLING THE BRUSH (65BTS double brush versions)
To assemble the brushes to bush head unit, which for reasons of packaging are supplied disassembled
from the machine, proceed as follows:
1. Take all necessary steps to ensure that the device is in a safe condition (see “ MACHINE SAFETY ”).
CAUTION : these operations must be carried out using protective gloves to avoid any possible
contact with the edges or tips of metal objects.
2. Stand on the left side of the appliance.
3. Remove the left side splash guard support (1) ( Fig. 1 ).
4. Remove the brush hub support carter (2) from the brush head body ( Fig. 2 ), remember to move the
retainer blade (3) downwards before removing the brush hub support ( Fig. 3 ).
5. Insert the rear brush in the tunnel ( Fig. 4 ), positioning the pentagonal driving pins (4) in the
pentagonal slit (5) in the brush ( Fig. 5 ).
6. Insert the brush hub support carter (2) into the brush head base ( Fig. 6 ), correctly positioning the
hexagonal pin (6) in the brush hub support into the hexagonal slit (7) in the brush (
Fig. 7
).
N.B.
: To fix the brush hub support carter to brush head body, insert the retainer blade (3) into the
slot (8) in the brush hub support carter (
Fig. 8).
7. Repeat the operations described above for the front brush as well.
N.B. : The brush bristles are properly positioned if they form an X when viewed from above. Both
vertices, of the shortest height, should converge towards the centre.
8. Repeat the operations in reverse order to reassemble all the parts.
1
2
1 2
3
3
2
6
4
5
4 5
3 6
8
7
7 8
INSTALLING THE ABRASIVE PAD (BTO versions)
For packaging reasons, the brush is supplied disassembled from the device. To assemble it on the brush
head unit, proceed as follows:
1. Take all necessary steps to ensure that the device is in a safe condition (see “ MACHINE SAFETY ”).
CAUTION
: these operations must be carried out using protective gloves to avoid any possible
contact with the edges or tips of metal objects.
2. With the brush head up, insert the abrasive pad in the lower part of the brush head ( Fig. 1 ).
1
20