Colorjet VerveLED VLY 2513 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 56

background image

Page | 7

VERVE LED

3. Safety Precautions

Before operating the printer and Printer Manager software for the first time, please read the document
carefully and follow all the usage instructions. While using the printer, kindly follow all the safety
instructions which are given below:

Fire Prevention

Inks and solvents must be enclosed in a special storage cabinet for inflammable liquids or within a separate
storage room and must be clearly identified to meet the professional requirements of safety regulations.
Ink storage must be strictly in compliance with local fire regulations for the use and storage of
combustibles.

Ventilation

In order to prevent the danger caused by volatile gas accumulation, the storage room must have sufficient
ventilation.

Note

: Solvent gas specific gravity is greater than the air, it would accumulate near the floor. Installation

work in the vicinity of electrical equipment must confirm the GB/T standards, national electrical regulation
requirements for level II sites, and installation by a corresponding qualification of the professional
electrical contractor.

4. Electric Requirements

Before installing the printer, the below mentioned electrical requirements should be confirmed:

•

Total Power Consumption is 7KW.

•

Machine needs single phase AC 220V, 30Amps (+ / - 10%), 50/60Hz.

•

Uninterrupted power supplies (flicker free) should be provided as it has digital circuit.

•

Exclusive Earthing should be required for printer and it should not be shared with UPS and
Building's common Earth.

•

Printer and computer must share same exclusive earthing.

Proper Earth Connection

The trouble-free printing depends on the earth connection provided to the machine. In some cases, the
media  generates  static  and  excessive  charges  that  can  damage  the  Print  Head  as  well  as  affect  the
placement  of  printing  dots.  Thus,  one  should  provide  the  proper  earth  connection  before  using  the
printer.

Precautions:

•

A separate earth connection should be provided to the machine

•

The earth resistance should be in the range of 4-5 ohms

Note

: Ensure that the earth point for the Printer and PC should be same for the safety of interfaces.

«
...
6
7
8
9
10
...
»

Содержание VerveLED VLY 2513

























































Отзывы:

Нет отзывов

Похожие инструкции для VerveLED VLY 2513

Бренд: TallyGenicom Страницы: 3

Бренд: QMS Страницы: 2

ApeoSport C5540I

Бренд: Fuji Xerox Страницы: 108

INFOPRINT HI-LITE COLOR 4005-HC2

Бренд: IBM Страницы: 10

Бренд: Konica Minolta Страницы: 432

Бренд: Thermotron Страницы: 10

Бренд: Oki Страницы: 109

Бренд: Unytouch Страницы: 12

Бренд: Intermec Страницы: 282

WorkCentre 5687 Series

Бренд: Xerox Страницы: 2320

VersaaLink B600

Бренд: Xerox Страницы: 170

Бренд: Epson Страницы: 35

WorkForce WF-7610

Бренд: Epson Страницы: 16

Бренд: Epson Страницы: 4

Бренд: Epson Страницы: 107

Бренд: Epson Страницы: 153

Бренд: Epson Страницы: 187

Бренд: Epson Страницы: 206

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды