Cognex 1AAU Скачать руководство пользователя | Manualshive

Страница: 27 / 44

background image

8405 Vision System Specifications

Specifications

8405

Minimum Firmware
Requirement

In-Sight version 5.1.1

Job/Program Memory

512MB non-volatile flash memory; unlimited storage via remote network device.

Image Processing
Memory

512MB SDRAM

Sensor Type

1/2.5 inch CMOS, rolling shutter

Sensor Properties

7.13mm diagonal, 2.2 x 2.2µm sq. pixels

Maximum Resolution
(pixels)

1

2592 x 1944

Electronic Shutter
Speed

32µs to 1000ms

Acquisition

Rapid reset, progressive scan, full-frame integration.

Bit Depth

256 grey levels (8 bits/pixel)

Frames Per Second
(FPS)

2

13 FPS

Lens Type

C-Mount

Trigger

1 opto-isolated, acquisition trigger input. Remote software commands via Ethernet. (RS-232C
available when using the optional CIO-MICRO I/O module.)

Discrete Inputs

None. (Eight additional general-purpose inputs available when using the optional CIO-MICRO
I/O module.)

Discrete Outputs

2 opto-isolated, NPN/PNP high-speed output lines. (Eight additional general-purpose outputs
available when using the optional CIO-MICRO I/O module.)

Status LEDs

Network, 2 user-configurable.

Network
Communication

1 Ethernet port, 10/100/1000 BaseT with auto MDIX. IEEE 802.3af or 802.3at TCP/IP Protocol.
Supports DHCP (factory default), static and link-local IP address configuration.

Serial Communication

None. (RS-232C: 4800 to 115,200 baud rates when connected to the optional CIO-MICRO I/O
module.)

Power

Class 2 Power over Ethernet (PoE) device.

Note

: The In-Sight 8100, 8200 and 8400 series vision system must be connected to a

Class 0, 2, 3 or 4 PoE power source, rated for at least 6.49 Watts.

Power Type

PoE Type A and Type B.

Power Consumption

6.49 W maximum per Class 2 PoE.

Current

Per Class 2 PoE requirements.

Voltage

48VDC nominal, applied from a Class 2 PoE source, which is typically powered from some
other voltage.

Material

Die-cast zinc housing.

Finish

Painted.

Mounting

Four M3 threaded mounting holes (1/4-20 and M6 mounting holes also available on
accessory BKT-IS8K-01 mounting bracket).

1

You can configure the number of image sensor rows and set them in the In-Sight Explorer software. If you decrease the number of rows, it
increases the frames per second acquired by the vision system. Refer to the AcquireImage topic in the

In-Sight

®

Explorer Help

file for more

information.

2

Maximum frames per second are job-dependent, based on the minimum exposure for a full image frame capture using the dedicated
acquisition trigger, and assumes there is no user interface connection to the vision system.

27

Specifications

«
...
25
26
27
28
29
...
»

Содержание 1AAU













































Отзывы:

Нет отзывов

Похожие инструкции для 1AAU

Бренд: Janome Страницы: 30

GPSMAP 5008 - Marine GPS Receiver

Бренд: Garmin Страницы: 2

Бренд: Janome Страницы: 26

WERTARBEIT N 656D Free Arm

Бренд: W6 Страницы: 102

Бренд: Pfaff Страницы: 12

Бренд: Pulsar Страницы: 21

Бренд: IMER Страницы: 11

Бренд: JUKI Страницы: 8

Бренд: Mitsubishi Electric Страницы: 12

Бренд: Mitsubishi Electric Страницы: 20

Бренд: Mitsubishi Electric Страницы: 28

Бренд: Radio Zeeland DMP Страницы: 60

Бренд: artisan Страницы: 36

Бренд: Singer Страницы: 20

Бренд: Life Fitness Страницы: 3

Бренд: Frister Rossmann Страницы: 46

Бренд: ZOJE Страницы: 24

Бренд: ZOJE Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды