Cognex 1AAU Скачать руководство пользователя

Страница: 13 / 44

Installation

Read this section to learn how the vision system connects to its standard components and accessories. For a list of

options and accessories, contact your Cognex sales representative.

Note

: Cables are sold separately.

CAUTION

All cable connectors are keyed to fit the connectors on the vision system. Do not force the connections

or damage may occur.

Install the Mounting Bracket (BKT-IS8K-01)

Note

When attaching the 8100, 8200, or 8400 series vision system to the mounting bracket, use the M3 screws

supplied with the mounting kit.

When attaching the 8505P vision system to the mounting bracket, use M3x8mm socket head screws.

If using the 1/4-20 or M6 mounting holes, the thread length of the screw should not exceed 8mm.

For more information, refer to

Mounting Bracket (BKT-IS8K-01)

on page 42

CAUTION

It is recommended that the vision system be grounded, either by mounting the vision system to a fixture

that is electrically grounded or by attaching a wire from the vision system's mounting fixture to frame ground or Earth
ground.

1. Align the mounting bracket with the mounting holes on the vision system.

2. Insert the M3 screws into the mounting holes and tighten using a 2.5mm hex wrench. The maximum torque is

0.3 Nm (2.5 in-lb).

8100/8200/8400 Series Vision System

8505P Vision System

Installation

Содержание 1AAU













































Результаты поиска

Содержание 1AAU

Отзывы:

Похожие инструкции для 1AAU

Бренды по названию

Популярные бренды

Cognex 1AAU, Справочное руководство

Результаты поиска

Содержание 1AAU

Отзывы:

Похожие инструкции для 1AAU

Бренды по названию

Популярные бренды