Cognex 1AAU Скачать руководство пользователя

Страница: 16 / 44

Connect the CIO-MICRO I/O Module (Optional)

The following steps illustrate how to connect the vision system to the In-Sight CIO-MICRO I/O module.

Note

The CIO-MICRO I/O module supports In-Sight 8000 series vision systems with firmware version 5.3.0 and

higher.

The In-Sight 8505P vision system must be connected to a Class 0, 3 or 4 PoE power source, rated for at

least 12.95 Watts. The CIO-MICRO I/O module is a Class 2 PoE device and therefore cannot be used to

supply power to the In-Sight 8505P vision system via the I/O module's PoE port. Instead, connect the

In-Sight 8505P vision system's Ethernet cable to a Class 0, 3 or 4 PoE power source and establish a

connection to I/O module over the local area network using In-Sight Explorer. For more information, see

Connect the Ethernet Cable

on page 15

I/O wiring or adjustments to I/O devices should be performed when the vision system is not receiving power.

CAUTION

Never connect the I/O module to a power source other than 24VDC. Any other voltage creates a risk of

fire or shock and can damage the hardware. Do not connect the 24VDC power source to any terminals other than
the 24VDC + and – power terminals.

1. Verify that the 24VDC power supply is unplugged and not receiving power.

2. Use a screwdriver to loosen the I/O module's power terminals (labeled 24VDC + and –).

3. Insert the 24VDC + and – wires (16 - 22 AWG, solid or stranded wire) from the power supply into the 24VDC +

and – terminals on the I/O module.

4. Tighten the screw terminals with the screwdriver to secure the wire leads in the terminal block; the maximum

torque is 0.1921 Nm (1.7 in-lb).

Installation

Содержание 1AAU













































Результаты поиска

Содержание 1AAU

Отзывы:

Похожие инструкции для 1AAU

Бренды по названию

Популярные бренды

Cognex 1AAU, Справочное руководство

Результаты поиска

Содержание 1AAU

Отзывы:

Похожие инструкции для 1AAU

Бренды по названию

Популярные бренды