Cognex 1AAU Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 44

background image

8400, 8401 & 8402 Vision System Specifications

Specifications

8400

8400C

8401

8401C

8402

8402C

Minimum Firmware
Requirement

In-Sight
version 5.2.0

In-Sight
version 5.5.0

In-Sight
version 5.2.0

In-Sight
version 5.5.0

In-Sight
version 5.2.0

In-Sight
version 5.5.0

Job/Program Memory

512MB non-volatile flash memory; unlimited storage via remote network device.

Image Processing
Memory

512MB SDRAM

Sensor Type

1/1.8 inch CMOS, global shutter

Sensor Properties

3.6mm diagonal, 4.5 x 4.5μm
sq. pixels

7.38mm diagonal, 4.5 x 4.5μm
sq. pixels

9mm diagonal, 4.5 x 4.5µm sq.
pixels

Maximum Resolution
(pixels)

1

640 x 480

1280 x 1024

1600 x 1200

Electronic Shutter
Speed

14µs to 520ms

17.4µs to 750ms

20µs to 940ms

Acquisition

Rapid reset, progressive scan, full-frame integration.

Bit Depth

256 grey
levels (8
bits/pixel)

24-bit color

256 grey
levels (8
bits/pixel)

24-bit color

256 grey
levels (8
bits/pixel)

24-bit color

Frames Per Second
(FPS)

2

217 FPS

135 FPS

76 FPS

45 FPS

53 FPS

33 FPS

Lens Type

C-Mount

Trigger

1 opto-isolated, acquisition trigger input. Remote software commands via Ethernet. (RS-232C
available when using the optional CIO-MICRO I/O module.)

Discrete Inputs

None. (Eight additional general-purpose inputs available when using the optional CIO-MICRO
I/O module.)

Discrete Outputs

2 opto-isolated, NPN/PNP high-speed output lines. (Eight additional general-purpose outputs
available when using the optional CIO-MICRO I/O module.)

Status LEDs

Network, 2 user-configurable.

Network
Communication

1 Ethernet port, 10/100/1000 BaseT with auto MDIX. IEEE 802.3af or 802.3at TCP/IP Protocol.
Supports DHCP (factory default), static and link-local IP address configuration.

Serial Communication

None. (RS-232C: 4800 to 115,200 baud rates when connected to the optional CIO-MICRO I/O
module.)

Power

Class 2 Power over Ethernet (PoE) device.

Note

: The In-Sight 8100, 8200 and 8400 series vision system must be connected to a

Class 0, 2, 3 or 4 PoE power source, rated for at least 6.49 Watts.

Power Type

PoE Type A and Type B.

Power Consumption

6.49 W maximum per Class 2 PoE.

Current

Per Class 2 PoE requirements.

Voltage

48VDC nominal, applied from a Class 2 PoE source, which is typically powered from some
other voltage.

Material

Die-cast zinc housing.

1

You can configure the number of image sensor rows and set them in the In-Sight Explorer software. If you decrease the number of rows, it
increases the frames per second acquired by the vision system. Refer to the AcquireImage topic in the

In-Sight

®

Explorer Help

file for more

information.

2

Maximum frames per second are job-dependent, based on the minimum exposure for a full image frame capture using the dedicated
acquisition trigger, and assumes there is no user interface connection to the vision system.

25

Specifications

«
...
23
24
25
26
27
...
»

Содержание 1AAU













































Отзывы:

Нет отзывов

Похожие инструкции для 1AAU

Бренд: Singer Страницы: 12

Бренд: Stamina Страницы: 15

Бренд: Dürkopp Adler Страницы: 84

Hand and Electric

Бренд: Essex Electronics Страницы: 12

Бренд: HIGHLEAD Страницы: 35

Бренд: Garudan Страницы: 67

Бренд: Duerkopp Adler Страницы: 38

Бренд: Singer Страницы: 39

Бренд: JUKI Страницы: 12

Бренд: Brother Страницы: 45

Бренд: Brother Страницы: 17

Бренд: Riccar Страницы: 18

Бренд: Riccar Страницы: 28

Бренд: Riccar Страницы: 45

President Series

Бренд: Graco Страницы: 22

Бренд: Life Fitness Страницы: 3

Victor Reader ClassicX 3.3

Бренд: Humanware Страницы: 22

Бренд: Baby Lock Страницы: 35

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды