6
English
Congratulations on having purchased a Coemar product. You can be assured that you have a fixture of the highest quality, both in
componentry and in the technology used. We renew our invitation to you to complete the service information on the previous page, to
expedite any request for service information or spares (in case of problems encountered either during or after installation). This infor-
mation will assist in providing prompt and accurate advice from your Coemar service centre.
Following the instructions and procedures outlined in this manual will ensure the maximum efficiency of this product for years to
come.
1.1. Packaging
Open the packaging and ensure that no part of the equipment has suffered damage in transit. In case of damage to the equipment,
contact your carrier immediately by telephone or fax, following this with formal notification in writing.
Packing list
Ensure the packaging contains:
1 Infinity Spot S
1 instruction manual
1 Cam-lock support brackets
1.2. Transportation
The
Infinity Spot S
should be transported in its original packaging or in an appropriate flight case.
1. Packaging and transportation
2. General information
2.1. Important safety information
Fire prevention:
1.Infinity Spot S
utilises a Philips MSR GOLD 300 FastFit; the use of any alternative lamp is not recommended and will null and void
the warranty of the fixture.
2.
Never locate the fixture on any flammable surface.
3.
Minimum distance from flammable materials: 0,5 m.
4.
Minimum distance from the closest illuminable surface: 2 m.
5.
Replace any blown or damaged fuses only with those of identical values. Refer to the schematic diagram if there is any doubt.
6.
Connect the projector to mains power via a thermal magnetic circuit breaker.
Preventing electric shock:
1.
High voltage is present in the internals of the unit. Isolate the projector from mains supply prior to performing any function
which involves touching the internals of the unit, including lamp replacement.
2.
For mains connection, adhere strictly to the guidelines outlined in this manual.
3.
The level of technology inherent in the
Infinity Spot S
requires the use of specialised personnel for all service applications;
refer all work to your authorised
Coemar
service centre.
4.
A good earth connection is essential for proper functioning of the projector. Never operate the unit without poper earth connection.
5.
Mains cables should not come into contact with other cables.
6.
Do not operate the projector with wet hands or in an area where water present
7.
The fixture should never be located in an exposed position, or in areas of extreme humidity. A steady supply of circulating air
is essential.
Protection against ultraviolet radiation:
1.
Never turn on the lamp if any of the lenses, filters, or the carbon fibre housing is damaged; their respective functions
will only operate efficiently if they are in perfect working order.
2.
Never look directly into the lamp when it is operating.
Safety:
1.
The projector should always be installed with bolts, clamps, and other fixings which are suitably rated to support the weight
of the unit.
2.
Always use a secondary safety chain of a suitable rating to sustain the weight of the unit in case of the failure of the primary
fixing point.
3.
The external surface of the unit, at various points, may exceed 150°C. Never handle the unit until at least 10 minutes have
elapsed since the lamp was turned off.
4
.Always replace the lamp if any physical damage is evident.
5.
Never install the fixture in an enclosed area lacking sufficient air flow; the ambient temperature should not exceed 35°C.
6.
Wait at least 10 minutes after the unit has been turned off prior to attempting to replace the lamp. Always use gloves while replacing
the lamp.
7
.The proejctor contains electronic and electrical components which should under no circumstances be exposed to contact with
water, oil or any other liquid. Failure to do so will compromise the proper functioning of the projector.
Articulated movement
The projector has a pan range of 540° in its base and a tilt range 262° in its yoke; do not obstruct the projector whilst it is undertaking
articulated movement.
Forced ventilation
You will note several air vents on the body of the projector. To avoid any problems associated with overheating, never obstruct any of
these vents as this may seriously compromise the proper operation of the unit.
