Cobra CS9 Скачать руководство пользователя страница 32

Страница: 32 / 35

Appendix B: Gas Conversion

Moffat Ltd, August 2012

Revision 3

Moffat Cobra Series CS9 - Gas Salamander

Gas Regulator

- NAT Gas / LPG / Butane Only.

NOTE: The regulator supplied is convertible

between Natural Gas and LP Gas, but

it’s outlet pressure is fixed ex-factory

and is NOT to be adjusted.

1. Ensure that the gas supply is turned 'Off' at

the mains.

2. Unscrew the hexagonal cap (23mm A/F) from

the regulator.

3. Un-clip the plastic pin from the cap, reverse

the pin and re-fit it back to the cap the correct

way for the gas type to be used.

(Either ‘LP’

or ‘NAT’ should be visible on the flank of

the pin once re-fitted to the cap)

4. Screw the cap back into the regulator hand

tight only.

- Town Gas Only.

1. Unscrew and remove the slotted cap from the

regulator.

2. Turn on the gas supply and the appliance.
3. Adjust the pressure djusting nut to achieve the

correct burner operating pressure.

NOTE:

The operating pressure to be

measured at the manifold test point

and with both burners operating at

the 'High Flame' setting.

4. Turn off the mains gas supply and bleed the

gas out of the appliance gas lines.

5. Turn on the gas supply and the appliance.
6. Verify the operating pressure remains correct

(Re-adjust the regulator if required).

7. Screw the cap nut back onto the regulator.

NOTE

, Pin rotated

for Natural Gas

NOTE

, Pin rotated

for LPG

Pressure Adjusting

Screw

Cap Nut

Figure b3

Figure b4

Содержание CS9




































Результаты поиска

Содержание CS9

Отзывы:

Бренды по названию

Популярные бренды

Cobra CS9, Руководство по обслуживанию

Результаты поиска

Содержание CS9

Отзывы:

Бренды по названию

Популярные бренды