manualshive.com logo in svg

Cobra CS9, Руководство по обслуживанию

Поделиться
Скачать
Cobra CS9 Скачать руководство пользователя страница 12

3 

Operation 

8 

© 

Moffat Ltd, August 2012 

Revision 3 

Moffat Cobra Series CS9 - Gas Salamander 

NOTE:  A full user’s Operation Manual is supplied with the product and can be used for further 

referencing of installation, operation and service. 

3.1    Description of Controls 

Gas Control Knobs 

๐

     OFF Position. 

    HIGH Flame. 

    LOW Flame. 



Cobra salamanders provide two independently 
controlled heat zones. 



High speed grilling is provided by the two  
infrared gas burners in the ceiling of the  

grilling compartment. 



The left hand gas control knob and right hand 
gas control knob operate the left side and right 

side burners respectively, independently of 

each other. 



Each burner is provided with a manually lit pilot 
burner and flame failure protection. 

Rack 

Handles

 

3.2    Operation 

Lighting the Main Burners 

1.  Rotate the control knob anti-clockwise to the 

position marked HIGH. 

2.  Manually light the main burner. 

- hold the gas control knob depressed for ap-

prox. 10 - 15 secs then release. 

3.  Once lit, the main burner will be burning at full 

rate.  For a lower heat, push in the gas control 
knob and turn fully anti-clockwise to the LOW 

position. 

4.  Also for intermediate heat, position the control 

knob between the HIGH and LOW positions. 

5. Repeat 

Items 

1 to 4

 to light the second main 

burner. 

WARNING: 

 

A

LWAYS

 

SET

 

THE

 

GAS

 

CONTROL

 

TO

 

THE

 'HIGH' 

POSITION

 

WHEN

 

LIGHTING

 

THE

 

MAIN

 

BURNER

. 

I

F

 

THE

 

MAIN

 

BURNER

 

GOES

 

OUT

 

DURING

 

NORMAL

 

OPERATION

 

OR

 

FOR

 

ANY

 

REASON

, 

WAIT

 3 

MINUTES

 

BEFORE

 

ATTEMPTING

 

TO

 

RE

-

LIGHT

 

THE

 

MAIN

 

BURNER

 

Содержание CS9




































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды