Clifford Responder LE 3.3X страница 18 Скачать руководство пользователя

Страница: 18 / 56

3
4
5
6

A U

button: Remote Beeps

Disarm LED

OFF

: The remote will not emit beeps except when pro-

gramming.

Disarm LED

ON:

The remote will emit beeps normally.

Disarm LED blinking: The remote will emit beeps only for alarm

trigger messages from the alarm system.

button: Runtime Low Alert feature

Note:

This feature is not available on the 1-way remote.

Remote Start LED OFF: The remote will ignore Runtime Low Alert

messages.

Remote Start LED ON: The remote will emit feedback output for

Runtime Low Alert messages.

These messages will be automatically sent while Remote Start is ON to

alert you when the runtime remaining is at 3 minutes, and again at 1

minute before shut down.

Note:

This feature is not available on the 1-way remote

A U

button: Page mode/Power saver

Note:

This feature is not available on the 1-way remote.

Aux LED

OFF:

The remote will not wake up and listen for messages

from the system to extend battery life.

Note:

This means the remote

will not receive alarm trigger pages.

Aux LED

ON:

the remote will wake up to listen for messages from the

system

Aux LED blinking: Power saver mode (see note below)

Note:

Power saver automatically turns off the remote pager if a but-

ton on the remote has not been pressed for more than 72 hours and

will be restored after any button on the remote is pressed.

▀

▀
▀

▀

Содержание Responder LE 3.3X

























































Результаты поиска

Содержание Responder LE 3.3X

Отзывы:

Похожие инструкции для Responder LE 3.3X

Бренды по названию

Популярные бренды

Clifford Responder LE 3.3X, Руководство пользователя

Результаты поиска

Содержание Responder LE 3.3X

Отзывы:

Похожие инструкции для Responder LE 3.3X

Бренды по названию

Популярные бренды